Related Manuals for Pudu Puductor Robot
Summary of Contents for Pudu Puductor Robot
- Page 1 V1.0 User manual PuduTech Copyright © 2020 Pudu Technology Inc. All Rights Reserved.
-
Page 2: Table Of Contents
Copyright © 2020 Pudu Technology Inc. ALL RIGHTS RESERVED. Instructions for use Without the express written permission of Pudu Technology Inc., no unit or individual may Environmental notes imitate, reproduce, copy or translate the contents of this manual in part or in whole, the dissemination by any means (electronic, photocopying, recording, etc.) shall not be carried... -
Page 3: Safety Instructions
Safety Instruction Service functions Map settings Instructions for use Voice settings 1. DO NOT block the port of disinfectant spray, and DO NOT put anything into the port. Speed settings 2. DO NOT drag the robot during the disinfection task, if necessary, tap the screen, and then push it after the pause, the disinfection mode pauses for 20s, and the robot will Version upgrade automatically resume moving after the pause. -
Page 4: Environmental Notes
User manual User manual Environmental notes 1. The robot is suitable for use in flat environments such as floors, tiles, and thin carpets, it is not suitable for use in environments where there are steps, the slope is too large, or the environment is too tight. -
Page 5: Power And Power Requirements
User manual User manual Power and power requirements 9. There is a 35cm space between the two robots placed side by side at the standby point, and a clearance of 15cm from the rear wall and 35cm from the side wall. 1. -
Page 6: Safety Instructions
User manual User manual Safety instructions 13. The blind-spot recognition area of the robot is shown below. 1. DO NOT place any open flame on the robot, and DO NOT place any flammable solids, gases or liquids. 2. It is forbidden to do cleaning and maintenance work when the machine is powered on. 3. -
Page 7: Product Composition
Product Composition User manual Performance parameters Component description Model Operating voltage DC 23-29.4V Power input AC 100-240V, 50/60Hz [1] Vision positioning sensor Power output 29.4V-3.5A [2] Screen Charging time 6.5h [3] Depth vision sensor Battery lifetime 4~8h [4] Lidar [5] Power Switch Cruise speed 0.5~1.2m/s adjustable [6] Disinfection component... -
Page 8: Introduction To Disinfection Component
User manual User manual Introduction to disinfection component Disinfectant spray nozzle Top disinfectant refilling port Disinfection module Disinfectio startup knob indicators it is the disinfection module green indicates the power-on the startup module. If the disinfection module starts robot starts normally, you can see running, red indicates the the green indicator of the startup disinfectant is insufficient. -
Page 9: Product Use
Product Use User manual Power ON, Power OFF, Pause, Start Charging instructions Before each power-on Charging mode: Connect the charging interface of the robot to the charging cable to Move the robot directly below the visual mark ensure that the charging port of the robot is connected to the charging cable, if the before each power-on. -
Page 10: Disinfection Mode
User manual User manual Disinfection mode Pause While the robot is running, touch the screen to Disinfection mode: In the disinfection mode, the robot performs intelligent circular make the robot pause. motion according to the route selected by the user, after entering the route, the robot starts the disinfection component and starts atomizing the disinfectant to disinfect the environment;... -
Page 11: Alarm Display
User manual User manual Alarm display 4. Select or enter the indoor space area Disinfection mode 91 % of the disinfection task. In the following cases, the robot will stop working and give an alarm tone, the tablet Route Settings 5.Please make sure that the disinfection interface will prompt the corresponding instructions, and the machine will need your （m²）... - Page 12 Service functions User manual Speed settings Map settings With the “Speed settings” function, you can set the disinfection speed, supporting the speed settings of 0.5m/s, 0.6m/s, 0.7m/s, 0.8m/s and 0.9m/s. In the “Map settings” function, you can select from multiple maps. In the robot one-to-one parking mode, select the current map to configure the parking position for the robot.
- Page 13 Product Maintenance User manual Parking instructions Disinfection component, drive wheel and auxiliary wheel According to the size of the use scene location, there are three robot parking options available. Keep the disinfection component clean and tidy, for disinfectant spray ports, check and 1.
- Page 14 Troubleshooting User manual Sign maintenance POST fails No other objects (such as balloons, barbed wire, slogans, etc.) can be hung directly under the sign, and no billboards or safety exit signs can be hung near the sign; pay attention not to damage the sign during routine ceiling cleaning and maintenance, and the sign cannot If the robot has sufficient battery power, restart the robot under the positioning mark, if be moved or rotated.
- Page 15 4. Valid proof of purchase, documents and order number are available. alter the documents. 5. Damaged spare parts replaced during the free warranty period are owned by Pudu 5. The occurrence of collisions, burns, and artificial modifications,the introduction of Technology and should be returned as requested by the Company, otherwise the foreign objects (water, oil, sand, etc.), improper installation, failure to use and operate...
- Page 16 2. PuduTech’ stechnical support personnel will record your product information in If Pudu Technology engineers diagnosed that they must go to the site to solve the relevant forms. problem, the Company may assigns professional and technical personnel to provide 3.
- Page 17 User manual User manual After-sales Service Contact Main Parts Warranty If you have any question, please call our service hotline: 400-0826-660 PuduTech’ s after-sales service hours are: Monday to Saturday, 9:00 am to 12:00 am, Main components Warranty period 14:00 to 18:00 pm. Upper computer master control board 12 months Upper computer expansion board...
Need help?
Do you have a question about the Puductor Robot and is the answer not in the manual?
Questions and answers