Sealey VS301 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: pleaSe read TheSe inSTrucTionS careFullY. noTe The SaFe operaTional reQuireMenTS,
WarningS and cauTionS. uSe The producT correcTlY and WiTh care For The purpoSe For Which iT iS
inTended. Failure To do So MaY cauSe daMage and/or perSonal inJurY and Will inValidaTe The WarranTY.
pleaSe keep inSTrucTionS SaFe For FuTure uSe.
1. SaFeTY inSTrucTionS
Warning! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.

do noT use tools if damaged.

do noT use this tool for purposes other than for which they are designed.

Maintain tools in good and clean condition for best and safest performance.

Ensure that a vehicle which has been jacked up is adequately supported with axle stands.

Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.

Wear suitable clothing to avoid snagging. do noT wear jewellery and tie back long hair.

Keep children and unauthorised persons away from the work area.

Account for all tools and parts being used and do not leave them in or near the engine.

do noT use the thread repair kit when you are tired or under the influence of alcohol, drugs or intoxicating medicines.

do noT attempt to start engine or move vehicle, whilst tools are fitted and work is in progress.

Ensure any disconnected fuel pipes are plugged to avoid spillage.

Account for all tools and parts being used, do noT leave them in or near the engine. Return all parts to the case and store this in a

safe, dry, childproof location.
IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions,

or a proprietary manual, to establish the current procedure and data.
Warning! Failure to comply with these instructions may result in damage to the thread repair kit or vehicle and/or personal injury.

Warning! The warnings referred to in this guide cannot cover all possible conditions and situations that may occur. It must be understood

that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.
2. inTroducTion & SpeciFicaTionS
Comprehensive and time saving kit of spark plug thread repair tools especially suitable for the repair of deep seated plug configurations. Kit of
tools incorporates taper and plug taps together with intergrated ream. Stepped tap ensures correct alignment of seat cleaner in existing spark
plug hole. Extension tools allow easy access to the bottom of the plug recess. Includes set of plug inserts.
Specifications.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VS301
Plug tap: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M14x1.25
Step tap: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M14x1.25; M16x1.25
Insert lengths: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9mm and 15mm
Replacement inserts; . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VS301.9 (10pcs), VS301.15 (10pcs)
3. conTenTS
Item
1
2 Step Tap (M14x1.25; M16x1.25)
3
4
© Jack Sealey Limited
Description
Plug Tap (M14x1.25)
Wrench
T-bar
Original Language Version
INSTRUCTIONS FOR:
Spark plug Thread repair kiT
MODEL No:
Part No: Item
VS301.05 5
VS301.06 6 Seat Cleaner
VS301.03 7 Inserts 9mm/15mm
VS301.01 8 Allen Key (2.5mm)
VS301
Description Part No:
Insert Drive VS301.02
VS301.04
VS301.9/VS301.15
VS301 Issue No: 3(I)- 06/01/14