Haier EI35M(AE) Installation And User Instructions

ELECTRIC INSTANTANEOUS WATER HEATER
INSTALLATION AND USER INSTRUCTIONS
Model:EI35M(AE)
Dear customer,
Please read this instruction carefully before use to avoid product damage and danger
due to improper application.Please keep the instruction properly to provide reference
for maintenance personnel.
Safety notices
It must use 220V,50Hz single phase AC power supply, and using other power supplies
are strictly forbidden.
It must use air leakage switch, and using plug is strictly forbidden.
It must ensure the provision of circuits for household appliances and enough limit for
the existing fuse distribution board.
The reliable earthing line must be provided before power supply.
Touching the power switch with wet hands is strictly forbidden .If the water heater is not
used for a long time, the connection with power supply shall be cut off.
Do not sprinkle water on the human body directly during use of initial water. Adjust the
power selection switch and temperature demands.It is forbidden to use in case of
smaller water flow and that power selection switch is at maximum power, so as to avoid
scalding due to excess temperature.
Empty the water in the water heater if it is not used for a long time in winter,so as to
avoid being frozen ,resulting in damage of the container. Please notice that,cut off the
power supply before emptying!
Regularly remove the dirt for the shower head and filter screen so as to avoid any
block. For any part damaged or needed to be replaced,it must be replaced by special
parts by our company or by the maintenance personnel appointed by our company.
Attentions:Failure to comply with this instruction implies the risk of
accident,property loss and personal injury.
Product characteristics
*Safety
With water-electricity separation heating technology, safety test and earthing protec-
tion, independent leakage protection, fault self-diagnosis protection, anti-over-tempera-
ture, anti-dry-heating, anti-spraying and low water flow protection, the water quality is
purified by filter screen so as to extend the service life of water heater.
1
Technical parameter
Model
Rated Voltage(V)
Rated Frequency(Hz)
Rated Power(W)
Rated electric Current(A)
Rated Pressure(MPa)
Maximum temperature(°C)
External Dimensions(mm)
Net weight(kg)
*Model specifications subject to change without notice.
Installation
Drilling three holes,insert Insert the unit to
two screws into the wall the two screws
110mm
hole hole
hole
*THE UNIT MUST BE INSTALL BY ELECTRIC ENGINEER.
*Place of installation
1.This water heater shall be installed near to power socket,sewer and the place using
water. Installation without drainage is not allowed.
2.During installation,both the inlet and outlet water pipes must be placed at the bottom
of the water heater.Horizontal type installation for the water heater is not
allowed.(Fig.1B)
3.The wall for installation of water heater must be firm and solid and can bear four
times the weight of the water heater.
*Fixation of body (Fig.1A)
According to the position of fixing hole of the water heater, install the product on solid
wall or board.
3
EI35M (AE)
AC 220
50
3500
15.9
0.6
55
360*240*80
1.5
HEATER
MAX
MIN OFF
POWER CONTROL
Screw for final fixing
*Energy conservation
Power is adjustable and suitable for using in any season.
Owing to the instant-on function,pre-heating is not needed，with heat preservation，
water saving and energy conservation.
*High efficiency
Heater is specially designed with good thermal conductivity and its thermal efficiency
can be has high as 95%. Plus the advanced anti-scaling technology, scale cannot be
formed and the thermal transmission can be faster.
*Convenience
Without necessary preheating ,this product can provide you with hot water at desirable
temperature in several seconds after startup. It can start at low water flow, even at
lowest water flow of 1.3L/min. So that water heater could bring you more convenient
and faster bath.
Product structure drawing
1. Dismantle the front cover,trace out the location according to the position of the
mounting hole on the bottom cover,and drill three screw holes of φ5, with a horizontal
distance of 110mm. Firstly hang the water heater by ST4*32 countersunk screw with
sleeve, then fix the bottom screw to fasten the unit.
2.If installed on the board, dismantle the front cover,and directly install the bottom cover
with self-tapping screws in the position of mounting hole (Refer to installation diagram
for details).
Attention: Use only accessories provided with this water heater. Put on the front cover
only after confirming that the mounting screws are firm and reliable. Otherwise,the
water heater may fall off from the wall and cause damage and property loss!
*Connection of water pipe
First connect the water pipe and run the water for 2 minutes,make sure no leaks,only
after connect the Electric Power.
Looking at the Front view of the unit, the left side is outlet pipe, right side is inlet pipe(-
Fig.2A)
Fit the screen gasket at the inlet pipe and install the Flow control valve, then connect
the water pipe.
Connect the flexible tube to the outlet pipe. Check if all the Inlet/Outlet pipes are
connected well and all joints are well sealed,and no leaks.
CAUTION:
1.Do not install valve at outlet pipe, connect the shower tube to outlet pipe only.
2.Connect the shower tube to shower head only, Do not use as water inlet pipe.
HEATER
MAX
MIN OFF
POWER CONTROL
1.This water heater uses 220V,50Hz single phase AC power supply. Before using,-
check if its electric current,ammeter and wire capacity match together.
2.Power supply connection block must use air switch or leakage protection switch with
the specification ≥30A/220V and be provided reliable earthing .The quality of the switch
must comply with the national standards. The connected lines must meet the require-
ment of rated current value (≥30A).Before installation,for wire connections ,it shall be
carried out tightness check and wiped, so as to avoid being with stain, resulting in fire.
3.Power supply connection block must be provided reliable earthing.It is recommended
to install a qualified leakage switch in the circuit.
HEATER
MAX
MIN OFF
POWER CONTROL
2
4