DeWalt DCE200 Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Power Tool
  5. DCE200
  6. Manual

DeWalt DCE200 Manual

Hide thumbs Also See for DCE200:
Table of Contents

Advertisement

Quick Links

Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
FIG. A
Press jaw
1
Jaw arms
2
Jaw retention pin
3
Lock/release slide
4
Trigger switch
5
Reverse trigger switch
6
Diagnostics panel
7
Power ON/OFF switch
8
Micro USB port
9
7
8
9
6
5
15
13
11
10
Battery pack
10
Battery release button
11
Shoulder strap ring
12
LED Worklight
13
Shoulder strap clip
14
Main handle
15
Tool neck
16
12
4
16
14

WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
If you have any questions or comments about this or
any D
WALT tool, call us toll free at:
e
1-800-4-D
WALT (1-800-433-9258).
e
3
2
1
1

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCE200

Summary of Contents for DeWalt DCE200

  • Page 1 Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

  • Page 2: General Power Tool Safety Warnings

    GENERAL POWER TOOL SAFETY WARNINGS b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust WARNING! Read all safety warnings, mask, non-skid safety shoes, hard hat, or hearing instructions, illustrations and specifications protection used for appropriate conditions will reduce provided with this power tool.
  • Page 3 f ) Keep cutting tools sharp and clean. Properly modifying the press tool for other applications maintained cutting tools with sharp cutting edges are may damage the press tool, damage the less likely to bind and are easier to control. attachments and/or can result in a faulty installation.

  • Page 4: Additional Safety Information

    • Always wear gloves when operating tool and The label on your tool may include the following symbols. The handling materials. The ends of the materials can be symbols and their definitions are as follows: sharp and can cause serious personal injury. V ......
  • Page 5 • Do not store or use the tool and battery pack in 120V Max* (two 60V Max* batteries) product, it will operate locations where the temperature may reach or as a 60V Max* battery. exceed 104 °F (40 °C) (such as outside sheds or metal Shipping Mode: When buildings in summer).
  • Page 6 1-800-4-D WALT (1-800-433-9258) or (AWG or American Wire Gauge) for safety. The smaller visit our website www.dewalt.com. the gauge number of the wire, the greater the capacity of the cable, that is, 16 gauge has more capacity than 18 The RBRC®...

  • Page 7: Charger Operation

    Other types of batteries may overheat and burst * DCB107, DCB112, DCB113, DCB115, DCB118, DCB132: resulting in personal injury and property damage. The red light will continue to blink, but a yellow indicator light will be illuminated during this operation. Once the NOTICE: Under certain conditions, with the charger battery pack has reached an appropriate temperature, the plugged into the power supply, the charger can...

  • Page 8: Intended Use

    3. If the battery pack does not charge properly: a. Check operation of receptacle by plugging in a lamp The DCE200 Cordless Press Tool uses an electric motor to or other appliance; power a hydraulic piston pump. The pumping action forces a ram forward that forces closed a jaw set or attachment.

  • Page 9: Assembly And Adjustments

    Step 1: Download the CRIMP CONNECT™ System software before making any adjustments or removing/ to your computer at www.dewalt.com/crimpconnect. installing attachments or accessories. An Step 2: Follow the instructions in the software to create accidental start-up can cause injury.

  • Page 10: Preparing The Connection

    extensive property damage. Return damaged jaw FIG. E assembly to a D WALT service facility. WARNING: To reduce the risk of serious personal injury, prior to use, inspect workpieces for cracks, defects or wear. Defective workpieces may shatter. WARNING: Before turning on the press tool, be sure hands are clear of the jaws.

  • Page 11: Register Online

    2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS hazardous. To reduce the risk of injury, only D WALT...

  • Page 12: 90 Day Money Back Guarantee

    FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-D WALT (1-800-433-9258) for a free replacement. SPECIFICATIONS DCE200 20V Max* Ram force 7645–8550 lbs (34kN-38kN) Operating Temperature Range 14 °F–158 °F (-10 °C–70 °C)

  • Page 13: Troubleshooting Guide

    Troubleshooting Guide BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS Problem Possible Cause Possible Solution Tool does not turn ON when power ON/OFF Battery is not charged. Charge battery or use a new, fully charged battery. switch is pressed. Battery is not fully inserted into tool. Remove battery and reinsert fully into the tool.

Table of Contents