Perun V2 Hybrid User And Installation Manual
  1. Manuals
  2. Brands
  3. Perun Manuals
  4. Controller
  5. V2 Hybrid
  6. User and installation manual

Perun V2 Hybrid User And Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Perun V2 Hybrid replaces mechanical contacts in your airsoft replica or gel blaster and provides lots of
useful features. Optical and magnetic sensors allow to eliminate many moving parts that are prone to
damage, thus increasing the reliability. The elasticity of this unit gives you certainty, that replica made
from parts from different manufacturers will not have any incompatibility issues. Adaptive trigger
control allows switching from a very short trigger travel to a long one even in the field, with almost any
trigger, including stock ones.
Reading this manual will help you fully exploit this unit's potential and in case of encountering any
problems, you can look for solutions to them here.
Manufacturer:
Perun
Barwicka 8 St.
60-192 Poznań, Poland
e-mail:
info@perunairsoft.pl

Table of contents

1.
Technical data.................................................................................................................................. 2
2.
Installation ....................................................................................................................................... 3
3.
During the start-up .......................................................................................................................... 5
4.
Adaptive trigger control .................................................................................................................. 5
5.
Features and programming ............................................................................................................. 6
6.
Factory settings ............................................................................................................................... 8
7.
Diagnostic system ............................................................................................................................ 9
8.
Sensor check .................................................................................................................................. 12
9.
Modifications needed in Krytac and other gearboxes .................................................................. 13
Perun V2 Hybrid
User and installation manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V2 Hybrid and is the answer not in the manual?

Questions and answers

Summary of Contents for Perun V2 Hybrid

  • Page 1: Table Of Contents

    Perun V2 Hybrid User and installation manual Perun V2 Hybrid replaces mechanical contacts in your airsoft replica or gel blaster and provides lots of useful features. Optical and magnetic sensors allow to eliminate many moving parts that are prone to damage, thus increasing the reliability.

  • Page 2: Technical Data

    1. Technical data Recommended power sources Perun V2 Hybrid works with any power source that provides a voltage between 7 and 17 volts and can deliver enough current to ensure smooth cycling of the replica. Li-Po and Li-Ion batteries with a nominal voltage of 7.4, 11.1 or 14.8 volts are recommended.

  • Page 3: Installation

    Put the selector sticker on the selector plate (remove the metal part on the plate if present), in a place shown on the sticker set that came with Perun. If you are installing it in a replica manufactured by ICS or an MP5 by JG, use stickers “for ICS”. The sketch below shows, how does...
  • Page 4 Also check the trigger and the sector gear. In case Perun does not detect trigger, sector gear, or selector positions properly at any of these trials, please refer to solutions described on the scheme above or below: The selector must be on “SAFE”...

  • Page 5: During The Start-Up

    Every time, when connecting the battery to the replica, make sure that the selector is set to “SAFE”. This is a safety concern, but it also helps Perun find out, where the “SAFE” position is. If you will connect the battery with the selector on “SEMI” or “AUTO”, the replica may not shoot unless you switch to “SAFE”...

  • Page 6: Features And Programming

    5. Features and programming Supplementary video manual is available here: https://www.youtube.com/watch?v=2o4eWEYyw7c To enter the programming mode: For “SEMI” – keep the selector on “SEMI” for a couple of seconds, then go to “AUTO” and back, twice. (“SEMI” → “AUTO” → “SEMI” → “AUTO” → “SEMI”) Successful entry into the programming mode for “SEMI”...
  • Page 7 Function and Description LED color Precocking When shooting on semi, precocking keeps the piston in the rear position, ready for the shot. This decreases the time between pulling the trigger and the actual shot, increasing realism, and giving advantage in CQB fights. Yellow Correct precocking level must be set individually to each replica and according to user preferences.

  • Page 8: Factory Settings

    Function and Description LED color This function allows to lower the rate of automatic fire. 5 reduction levels are available: reduction 1 – 6% 2 – 12% 3 – 18% White 4 – 24% 5 – 30% Attention! Those are approximate values and may vary depending on replica configuration.

  • Page 9: Diagnostic System

    7. Diagnostic system Perun V2 Hybrid has a diagnostic system that will help you find the source, should you encounter a problem. After the battery is connected, the unit undergoes a start-up check, to make sure replica is ready to work. Successful completion of this check is indicated by a short green blink of the LED.
  • Page 10 Problem and LED color Description Main transistor or driver The main transistor or driver is damaged. The unit needs to be sent damage back for repair. Red and yellow blinking alternately Battery voltage sensing The battery detection system is malfunctioning. The unit needs to be malfunction sent back for repair.
  • Page 11 – brake and/or spring Perun brakes the gears fast with the piston in front position. Spring drop drop does not work enough to stop the sector...

  • Page 12: Sensor Check

    To check the sector gear sensor, it is best to open the gearbox and remove everything out of it, except for Perun and the sector gear (make sure to keep the shimming the same as in assembled replica, it can influence whether the sensor would work or not). Then spin the sector gear by hand and see,...

  • Page 13: Modifications Needed In Krytac And Other Gearboxes

    9. Modifications needed in Krytac and other gearboxes Some gearboxes need minor modification in order to allow installation of Perun V2 Hybrid. Here we describe some cases that are known to us. Never grind the electronic board instead! It can lead to permanent damage of the unit, even if no components and paths are visible in the area you want to modify.

Table of Contents