Shutter Button Connection Method; Structure Of Shutter Button; About The Led Lights; Battery Replacement Guide - Elecom P-SSB Series Manual

Structure of shutter button
Strap hole
Connection method
1
Turn on the Bluetooth
on your terminal
device.
* For settings on the terminal
device side, check the
instruction manual of the
terminal device you are
using.
To turn off the power
Reconnection

Troubleshooting

Does not turn on
It is possible that the remaining capacity of the battery is gone. Replace the battery.
When the remaining battery level becomes low, the red LED light will blink slowly. Upon confirming this state, replace with a new, unused battery as soon as possible.
Cannot be paired
Delete (or cancel) the registration information of this product from the smartphone and try to pair again.
Make sure that the Bluetooth function of the connected device is in a state that allows pairing. In general, it is necessary to enable the function through the settings on
the smartphone side. Please check the settings of the smartphone to be connected.
The procedure for opening the pairing mode differs depending on the smartphone to be connected. For smartphone operation procedures, also refer to the instruction
manual of your terminal device.
If your smartphone cannot successfully search for Bluetooth devices, try again after rebooting it.
Suddenly you are no longer able to reconnect despite always having been able to do so
Depending on your smartphone, registration information may be lost when it repeatedly tries to reconnect, and so you may not be able to reconnect automatically.
Restart your smartphone and turn the power on the Bluetooth product off and on again. Also, delete the connection information for the product on the smartphone side
and try pairing again.
Precautions regarding radio waves
The frequency band this product uses is also used by on-premise radio stations (requiring licensing) used for mobile identification performed in the production lines for
industrial (such as microwaves), scientific, and medical equipment, and by specified low-power radio stations (not requiring licensing).
Before using this product, confirm that no mobile radio identification station for mobile identification or specified low power radio station is being operated nearby.
In the rare event that radio wave interference occurs from this product to a local radio station for mobile identification, stop radio wave emission promptly and contact
the Elecom General Information Centre to consult about necessary countermeasures (e.g., setting up partitions, etc.).
In addition, contact the Elecom General Information Centre if any trouble such as radio wave interference occur from this product to specified low power radio station for
mobile identification.
Do not use this product in places where radio wave usage is prohibited, such as hospitals. Radio waves from this product may affect electronic equipment and medical
devices (e.g., pacemakers).
Because of the risk of interference to the safe operation of aircraft, use of this product in an aircraft is prohibited by aviation laws. Before boarding an aircraft, check that
the power of this product is turned off and do not use at any time after boarding.
Due to the characteristics of using radio waves, this product may cause radio interference with equipment that uses other radio waves under certain conditions.
Safety Precautions
Never disassemble or modify this product. Since this product is specified radio equipment
that has undergone construction design certification, it is prohibited by law to disassemble or
modify it. Also, products disassembled or modified are no longer subject to warranty.
Please use and store this product out of reach of children. Since this product contains
batteries and small parts, there is a danger of suffocation etc. if put in the mouth.
When not using this product for an extended amount of time, store with the battery removed.
The battery may leak or cause malfunction.
This product is not waterproof. Use and store in a place not subject to moisture such as
water.
We cannot assume any responsibility for incidental guarantees surrounding the use of this
product for damages such as malfunction of connected equipment, breakage or loss of
stored data, or opportunity loss in making telephone calls, etc.
Shutter Button Connection Method
About the LED lights
Green LED light is lit for 3 seconds
Green LED light blinks for 60 seconds
Green LED light is lit for 1 second
Shutter button
(Power button)
Red LED light blinks slowly
2 3
Press and hold the
shutter button on the
remote control of this
product for about 1
second to turn on the
power. (Pairing mode)
Press and hold the shutter button for 3 seconds.
* If there is no operation for more than 3 minutes in the connected state, the power will turn off automatically.
After turning on the power, in 3 seconds it enters reconnection mode and automatically reconnects
the smartphone that was connected the previous time.
Reconnection mode
Pairing mode
Light is off
Pairing completed
Battery replacement guide
4
Please select the When "Connected" is
device name displayed on the terminal
"BTselfie E" device, the connection has
displayed on the been completed.
terminal device.
* If you cannot connect within 60
seconds the power will turn off
automatically.
In "ELECOM CO., LTD. (Japan)" , no customer support is available to inquiries
about purchases or usage in/from any other countries than Japan. No foreign
languages other than Japanese is also available.
Replacement will be made under stipulation of the Elecom warranty, but not
available from outside of Japan.
A customer who purchases outside Japan will contact for inquiries the local
retailer in the country of purchase.
* The specifications and appearance of this product may be changed without prior
notice for product improvement purposes.
* The pictures and illustrations shown on packaging are for illustrative purposes
only. Be aware that there may be differences between the pictures/illustrations
and the actual product.
* Company names, product names, and other names in this manual are either
trademarks or registered trademarks.
* iPhone is a trademark of Apple Inc.
* The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by ELECOM CO., LTD. is under
license.
Battery replacement method
Open
Open the lid with a coin,
or a similar flat-shaped
object, and insert the
battery.
* Insert so that the positive
(+) end of the battery faces
upward.
Close the lid tightly with
a coin, or a similar
flat-shaped object.
* These illustrations are for illustrative purposes only.
* If you cannot connect
with the method
indicated on the left,
try again using the
Connection Method
.
2
MSC-P-SRB ver.111
Close