Sealey LS501 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instructions gloves
1. SAfETY
9
ensure the load sling adjuster is in sound condition and good working order. Take action for immediate repair or replacement of
damaged parts.
9
Use recommended parts only. The use of improper parts may be dangerous and invalidate the warranty.
9
ensure that the adjuster is capable of supporting the load that is to be raised. Maximum capacity 680kg.
9
Keep the adjuster clean for best and safest performance.
9
only use the adjuster in a suitable, well lit work area.
9
Keep the work area clean and free from unrelated materials.
9
ensure that all non-essential persons keep at a safe distance, whilst the adjuster is in use.
9
ensure load sling(s) are fully engaged in their karabiners and that the screw locks are securely closed.
9
Raise and lower the load in a smooth, controlled manner.
▲
DANGER! Use the adjuster for lifting only, NOT for supporting the lifting load.
Use a qualified person to lubricate and maintain the adjuster.
9
8
DO NOT use the adjuster if damaged.
8
DO NOT allow untrained persons to operate the adjuster.
8
DO NOT exceed the rated capacity (safe working load) of the adjuster.
8
DO NOT raise or lower the load with abrupt or jerky movements.
8
DO NOT attempt to lift a load if the load chains are kinked or knotted.
8
DO NOT shock the load adjuster by allowing the attached load to fall freely, even for very short distances.
DO NOT use the adjuster to drag the load across the floor. Always position the load directly below the adjuster.
8
8
DO NOT allow anyone to stand, or pass, beneath the raised load.
8
DO NOT use the adjuster for purposes other than that for which it was intended.
9
Store adjuster in a dry, childproof area when not in use.
2. INTRODUCTION
Handles and levels heavy, off centre loads quickly and easily. Ball bearing handle allows for a smooth and easy adjustment. Three adjustment
holes accommodate different sized engines. Ideal for car, van truck and marine engines. If used with cranes of capacity 680kg or more, the load
must be restricted to a 680kg maximum. Supplied with 4 x 275mm chains and 4 x 'l' shaped brackets with additional karabiner style screw links.
3. SAfE WORKING LOAD
LS 501
Safe Working Load = 680kg
4. SPECIfICATION
Model No: . . . . . . . . . . . . . . . . . LS501
Sling Span: . . . . . . . . . . . . . . . . 340mm
5. OPERATION
Refer to fig.1
IMPORTANT: Before using the load sling adjuster ensure that you have read and understood the safety instructions in Section 1.
4.1 ensure that the load sling adjuster is suspended from a lifting system in which all components are capable of supporting the load to be
lifted plus the load sling adjuster.
Confirm that the load does not exceed the safe working load of the adjuster.
4.2
Position the carriage (A) at the centre of the beam (B) and suspend the adjuster, via the carriage, from the hook or shackle of the lifting
4.3
device.
4.4 ensure that the slings/chains/ropes around the load are adequate and in good condition and that the load is directly below the adjuster.
Attach slings/chains/ropes to adjuster load brackets (C).
4.5
4.6 Start to raise load and check whether the adjuster beam remains level. If it does not, lower the load and adjust the carriage towards the
end of the beam which was low. Repeat this check and adjustment until the beam lifts horizontally.
NOTE: DO NOT attempt to reposition the carriage when the adjuster is under load.
© Jack Sealey limited
LOAD SLING ADJUSTER WITH BALL
BEARINGS 680KG CAPACITY
Model no:
Wear protective Warning
footwear
Original Language Version
LS501
lS501 Issue 2 (HF) 17/07/18