Table of Contents
Advertisement
Quick Links
CONTENTS
SAFETY PRECAUTIONS ............................2 ~ 4
OPERATING REQUIREMENTS ....................... 4
PRODUCT FEATURES ...............................4 ~ 6
MAIN PARTS IDENTIFICATION .................6 ~ 8
SETUP....................................................8 ~ 10
OPERATION .........................................10 ~ 15
........................................................
.........................................................
..................................
MAINTENANCE....................................16 ~ 18
.................................
FURTHER INFORMATION .....................18 ~ 21
FAQ .....................................................21 ~ 22
TROUBLESHOOTING............................22 ~ 23
SPECIFICATIONS ....................... BACK COVER
SPECIFICATIONS ....................... BACK COVER
Warranty card attached
Thank you very much for purchasing this Panasonic product.
Please read these operating instructions carefully before operation and maintenance.
Also, be sure to read the "SAFETY PRECAUTIONS" section (P.2 ~ 4) before use.
Failure to comply with instructions could result in injury or property damage.
Make sure that the correct information is written on the warranty card, including the date of
purchase and the name of the distributor. Keep the warranty card in a safe place along with the
operating instructions for future reference.
Panasonic
"
OPERATING INSTRUCTIONS
.........
..............................
.........................
2 ~ 4
"
Model No.
This product is for indoor use only.
11
12
PM2.5
13
14 ~ 15
16 ~ 17
17 ~ 18
18
Air Purifier
2 ~ 4
4
4 ~ 6
6 ~ 8
8 ~ 10
10 ~ 15
11
12
13
14 ~ 15
16 ~ 18
16 ~ 17
17 ~ 18
18
18 ~ 21
21 ~ 22
22 ~ 23
Advertisement
Table of Contents
Related Manuals for Panasonic F-PZT175H
Summary of Contents for Panasonic F-PZT175H
-
Page 1: Table Of Contents
SPECIFICATIONS ....... BACK COVER Warranty card attached Thank you very much for purchasing this Panasonic product. Please read these operating instructions carefully before operation and maintenance. Also, be sure to read the “SAFETY PRECAUTIONS” section (P.2 ~ 4) before use. -
Page 2: Safety Precautions
SAFETY PRECAUTIONS Please strictly follow Disconnect power supply before maintenance. For cleaning see "maintenance“ . This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for the safety. - Page 3 SAFETY PRECAUTIONS Please strictly follow WARNING In case of any abnormality or Do not disassemble or modify malfunction, stop using the the product. product immediately and disconnect the power. (Otherwise, the product may catch fire or malfunction, thus resulting in fire or electric shock.) (Otherwise, electric shock, fire or smoke may occur.)
-
Page 4: Operating Requirements
SAFETY PRECAUTIONS Please strictly follow CAUTION Keep the room well-ventilated Do not place the product near combustible materials such as when using the product lighted cigarette, incense, etc. together with a burner. (Otherwise, these may be absorbed (Otherwise, carbon monoxide into the product with possibility of fire.) poisoning may occur.) This product cannot remove carbon... - Page 5 Test outcome: eliminated 99% and above in 8 hours [Test number 13044083003-01] (With one type in variety of bacteria to test) 13044083003-01 Test organization: Panasonic Corporation Analysis Center Test method: measure the allergens adhered on the fabric in a test space of 23 m with ELISA...
-
Page 6: Main Parts Identification
PRODUCT FEATURES Test organization: Panasonic Corporation Analysis Center Test method: conduct verification by using 6-phase odor intensity in a test space of 23 m 23 m Deodorizing method: release nanoe ® nanoe ® Target: adhered cigarette odor Test outcome: odor intensity dropped to 1.2 after 2 hours [BAA33-130125-D01]... - Page 7 MAIN PARTS IDENTIFICATION Control panel (PM2.5 Concentration/ Timer Display Window) Filter cleaning PM2.5 Remote Human indicator Timer PM2.5 volume Filter replacement receiver sensor button button indicator indicator Light sensor PM2.5 nanoe ® indicator Clean sign Human Silent PM2.5 Light Power sensor nanoe ®...
-
Page 8: Setup
MAIN PARTS IDENTIFICATION nanoe indicator Human sensor indicator ® nanoe ® This indicator lights on to indicate that the The indicator lights on indicates human activity sensor is sensing. nanoe is being generated. ® (When the product stops operating, the nanoe will be generated in all ®... - Page 9 SETUP Install filters Lift up the front panel with both hands while holding down the guide lock with your thumbs and slowly lowering the front panel (2 pcs).(Front panel can only be opened about 15 degrees). 15° Notice Guide lock When opening the front panel, pay attention to the gap and corner position between the two panels to prevent your fingers being clamped.
-
Page 10: Operation
SETUP Power-on Install filters Close the front panel (2 pcs) slowly. Power-on. When connecting power, the odor sensor takes this moment as the baseline for the level of cleanliness, so it is recommended when the air in the room is clean (such as when there is no cigarette smoke). -
Page 11: Power Off/On Air Volume Silent Auto
OPERATION Power off/on Turn on or off. Press the button to operate. The product operates in auto air volume mode when it is used for the first time, (button lights then operates in the last mode when it was stopped. Press the button again, the product stops operating. -
Page 12: Pm2.5
OPERATION PM2.5 Quickly remove PM2.5. PM2.5 Press this button to quickly remove PM2.5 and automatically control the air volume (air volume indicator is off), until the indoor PM2.5 concentration is lower than the PM2.5 concentration baseline (factory setting is 35 µ /m (button lights PM2.5 PM2.5... -
Page 13: Timer
OPERATION Timer Each press of the button will switch the time in the order below on the PM2.5 concentration/ timer display window. About 15 seconds after the selection is (button lights completed, the setting will be automatically saved, and the setting is completed. PM2.5 2 hours timer Stop operation automatically after 2 hours. -
Page 14: Remote Control
OPERATION Remote control (touch screen) Remote control operation. Transmitter Operating methods The tape must be removed before use. Air volume Power off/on (otherwise, the battery cannot be button button powered on.) Silent Auto Timer button button Tape PM2.5 button When using, please point the signal transmitter to the product and use it within the effective PM2.5 range of the remote control receiver. - Page 15 OPERATION Remote control (touch screen) Battery replacement method (Panasonic CR2025 is recommended. ) Panasonic CR2025 The service life of the battery is approximately 1 year. (Assumed that the button is pressed 20 times a day) Pull out the battery holder...
-
Page 16: Maintenance
MAINTENANCE Notice WARNING Do not use the detergents Polish Make sure to disconnect the shown on the power before cleaning the right. product. (Otherwise, the product might operate with the possibility of electric shock or injury.) Do not operate the product when the When using chemically treated cloth, make composite and deodorizing filter is removed. -
Page 17: Filter Replacement
MAINTENANCE Dirt sensor (side) Pre-filter Body Composite and deodorizing filter Front panel black side (active carbon side) Composite and deodorizing filter (When the filter clean indicator is on (about once a month)) Clean the black side (Active carbon side) with a vacuum cleaner The Removal and installation method can be found on page 9 to 10. -
Page 18: When Idle For A Long Time
MAINTENANCE Filter replacement After replacing the filter, record the date installed on the label that came with the filter and attach it to the body, cover the previous date record. (Page 8 ) Connect the power, press simultaneously for about 3 seconds, the filter replacement indicator turns off, and the reset is completed. - Page 19 FURTHER INFORMATION About odor sensor dirt sensor · The sensor detects air pollutants and shows the pollution level by the clean sign. In auto operation, the product can optimize the air volume for purifying the air according to the detected pollutants.
- Page 20 FURTHER INFORMATION About brightness reaction Detects the indoor brightness by the light sensor, and automatically adjusts the brightness of the indicators and the air volume. When the room becomes dark during bed time, the indicator goes dim or lights off, and the product runs with low air volume.
-
Page 21: Faq
FURTHER INFORMATION About human sensor When the movement of a person or pet is detected, the air volume is automatically adjusted. When the generation of indoor dust is predicted, the product starts operating before the indoor air pollution spreads. (When the air volume is set to auto.) (Not all pet movements can be detected.) The sensor sensitivity is adjustable. -
Page 22: Troubleshooting
Why has the clean sign never Why is the human activity sensor changed? indicator always on without someone or pet moving? Such problems may occur because of the difference in sensitivity of sensor. (P. 19) When you use an electric room heater with swing function, if the indoor temperature ( 19 ) changes, the sensor could automatically... - Page 23 TROUBLESHOOTING If a problem is encountered, please investigate it by going through the following items. If the problem still persists, please disconnect the power and contact the dealer for repair. Possible situation Please confirm the following Automatic operation When the setting is “Auto”, the product will still operate with low air volume even if the air in the room is clean.
-
Page 24: Specifications
SPECIFICATIONS Model number Power supply 220 V ~ 50 Hz Air volume settings Turbo High Medium Silent Power consumption (W) Product dimension Width 758 mm X Deep 220 mm X Length 1412 mm 758 mm X 220 mm X 1412 mm Product weight The power consumption is lower than 2 W when the operation is stopped with the power connected.