Advertisement
2. INTRODucTION
Pistol grip design improves control and accuracy when carrying out repairs. Features a LEd work light, high and low power option, and a
Lithium-ion battery for prolonged usage. capable of inserting 100+ staples from one full charge. complete with staples; 100 x 0.6mm u-shaped,
100 x 0.8mm u-shaped, 100 x 0.6mm V-shaped.
3. SpEcIFIcATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RE024
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Li-ion 3.7V - 6600mAh
charging time: . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4hours
Replacement staples: . . . . . . . . . . . . . . . . . . . . (Packs of 100) RE06 (0.6mm), RE06V (0.6mm), RE08 (0.8mm)
4. OpERATION
4.1.
Fully charge the battery before first use. Plug the charger cable into an electrical outlet and connect into the charging port (see fig.1).
The charge indicator lights are on the top of the unit (see fig.2). The green LED will light when it is fully charged, charging is denoted by
a yellow LEd and low battery is the red LEd. unplug the cable once charged, and the unit is ready for use.
4.2.
choose a suitable heating repair pin and place it in the tip of the stapler.
4.3.
Set the power switch (see fig.2) according to the type of plastic (low for thin plastic, bumpers etc. high for thick or hard
plastic.)
4.4.
Keep the stapler perpendicular to the damaged surface.
4.5.
Press the switch button on the grip for 10 seconds until the pin is hot enough to weld. then press the pin gently against the damaged
surface.
4.6.
When the pin is half way into the plastic material stop pressing and release the power button. Wait for a few seconds until the repair
becomes firm.
4.7.
once plastic has cooled and staple is fully secure, pull stapler gun gently back to release.
4.8.
If the damaged surface is very long or wide, insert extra pins, 1/2 inch apart.
4.9.
cut off the pins with a side cutter, then grind the remains of the pin with a sander/grinder.
NOTE: DO NOT press the repair pins too hard as it may penetrate the plastic too far.
NOTE: Rest the stapler for 5 to 10 minutes after 40 cycles of continuous use in order to extend the life of the product.
fig.1
parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
undo the screw in the door in the base of the staple gun and remove the battery for correct disposal.
under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak's
registered compliance scheme. Jack Sealey Ltd's Batteries Producer Registration Number (BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMpORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack sealey Limited
Dispose of this product at the end of its working life in compliance with the Eu Directive on
Sole uK Distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. Edmunds, suffolk,
IP32 7AR
Environmental protection
WEEE Regulations
Battery Removal
Original Language Version
01284 757500
01284 703534
fig.2
www.sealey.co.uk
sales@sealey.co.uk
RE024
Issue: 1 - 09/04/14
Advertisement
