Summary of Contents for Energetica e.CLASSIC M HC
- Page 1 INSTALLATION MANUAL e. CLASSIC M HC e. CLASSIC M HC black www.energetica-pv.com V1.o - 26.11.2020...
-
Page 2: Table Of Contents
Information for the operator Applicable Documents Before and after installation Before installation After installation Electrical installation Electrical connections e.ISP - Energetica Integrated Shadow Protection Series connection Series connection / parallel connection General wiring Grounding Module installation Site conditions Suitable environmental conditions... -
Page 3: Introduction
- it can also lead to personal injury and property damage. These installation instructions describe the safe installation of the photovoltaic modules e.Classic M HC / e.Classic M HC black from Energetica Industries GmbH, hereinafter referred to as the PV module. -
Page 4: Safety Regulations
» Product data sheet for the e.Classic M HC or All electrical work may only be carried out by an officially e.Classic M HC black. certified specialist in accordance with the applicable »... -
Page 5: Before And After Installation
Before and after installation Before installation » » Read this manual carefully before installation. Never step on the modules or put any mechanical loads » Have the installation and maintenance of the PV modules on them. Do not drop any objects on the modules. »... -
Page 6: After Installation
Never use light concentrators such as mirrors or lenses. » Modules suspected of having an electrical problem should be returned to Energetica Industries GmbH, Energieplatz 1, A-9556 Liebenfels, Austria, for inspection, possible repair or replacement in accordance with the guarantee. -
Page 7: Electrical Connections
When selecting an inverter, please ensure that the All Energetica modules have intelligent electronics integrated inverters used have reverse current protection! in the module called e.ISP (Energetica Integrated Shadow Protection). Thanks to their 80 percent lower power loss compared to... -
Page 8: Series Connection
For detailed electrical data, please refer to the current product data sheet. If the module strings are connected in parallel, external Available at www.energetica-pv.com. diodes (blocking diodes adapted to the output) are requi- Only interconnect modules of the same type and the same red because the internal electronics adapted to the modle performance class to prevent damage to the modules. -
Page 9: Series Connection / Parallel Connection
Installation methods Inverter Parallel connection » Inverters with and without a transformer can be used. Please The solar modules can be connected in parallel to achive make sure beforehand that the inverters comply with all the desired amperage. » relevant standards in your country. If the modules are connected in parallel, the total ampe- rage is the sum of the amperages of the individual mo- dules. -
Page 10: General Wiring
In order to prevent electric shocks or fires, protective size of 6 mm. earthing must be attached to the frame of the solar mo dules and systems, even if Energetica photovoltaic modu les meet the requirements of safety class II. Grounding The national regulations must always be observed. -
Page 11: No Shade
If you use a special clamp, it must be tested for snow). compatibility by Energetica Industries. » Energetica solar modules can be used up to an altitude of 4000 m. Planning Check whether the maximum snow loads of the modules are suitable for the relevant snow load zone. -
Page 12: Transport And Care
» For transport, stack the product only on the special pallet electrically conductive parts on your body or clothing. provided by Energetica. » The maximum stacking height is two pallets. Stacking too In order not to damage the module surface, clean the... -
Page 13: Installation Variants
Installation variants Installation with clamps Point bearing with rail Line bearing 210 mm 210 mm 1/5 = 210 mm 1/5 = 356 mm no installation system in the junction boxes area Point bearing without rail 210 mm 210 mm 1/5 = 210 mm Please note the specification of the permissible static load and the clamping range on the following page. - Page 14 The following parameters were used for the listed Energetica test load values: clamp width = 40 mm and clamp depth = 10 mm. The system installer is responsible for determining the site-specific load requirements.
-
Page 15: Product Specifications
Product specifications Product line e.Classic Type e.Classic M HC e.Classic M HC black Performance classes Wp 365, 370, 375, 380, 385, 390 350, 355, 360, 365, 370 Length 1780 mm 1780 mm Width 1042 mm 1042 mm Frame thickness 36 mm... - Page 16 Notes Page 14...
Need help?
Do you have a question about the e.CLASSIC M HC and is the answer not in the manual?
Questions and answers