Related Manuals for hydro-s 7024510
Summary of Contents for hydro-s 7024510
- Page 1 Swimming Pool Heat Pump Installation and User Manual Models: 7024510 Hydro-S heat pump Type A5/32 7024511 Hydro-S heat pump Type A7/32 7024512 Hydro-S heat pump Type A10/32 7024513 Hydro-S heat pump Type A13/32...
-
Page 2: Table Of Contents
Please read carefully CONTENT INTRODUCTION ..........................2 SAFETY INSTRUCTIONS ........................3 ACCESSORIES ..........................5 DIMENSIONS ........................... 6 EXPLODED VIEW ..........................7 INSTALLATION ..........................9 CONTROLLER ..........................11 PARAMETER CHECKING AND ADUSTMENT................... 12 WIRING DIAGRAM ........................14 SPECIFICATIONS ..........................16 MAINTENANCE ..........................17 TROUBLESHOOTING ........................ -
Page 3: Introduction
READ THIS MANUAL CAREFULLY BEFORE STARTING UP THE UNIT. DO NOT THROW IT AWAY. KEEP IT IN YOUR FILES FOR FUTURE REFERENCE. BEFORE OPERATING THE UNIT, MAKE SURE THE INSTALLATION HAS BEEN CARRIED OUT CORRECTLY BY A PROFESSIONAL DEALER. IF YOU FEEL UNSURE ABOUT OPERATION, CONTACT YOUR DEALER FOR ADVICE AND INFORMATION INTRODUCTION This manual... -
Page 4: Safety Instructions
pressure protections, overload protection, etc. Safe using The swimming pool heat pump works without oil, gas or other hazardous substance. So adopting heat pump to heat your swimming pool, it can avoid potential risk. Moreover there are no gas connections, and fuel tank is also no need. No risk of intoxication, smell or pollution because of gas and fuel leakage. - Page 5 Be sure to use the provided or specified parts for the installation work. The use of defective parts could cause an injury due to possible fire, electric shocks, the unit falling etc. Perform the installation securely and please refer to the installation instructions. Incorrect installation could cause an injury due to possible fire, electric shocks, the unit falling, leakage of water etc.
-
Page 6: Accessories
due to the high speed running fan or an electrical shock. Do not continue to run the unit when there is something wrong or there is a strange smell. The power supply needs to be shut off to stop the unit; otherwise this may cause an electrical shock or fire. -
Page 7: Dimensions
DIMENSIONS (Unit: mm) A5/32 A7/32 A10/32 A13/32 425.5 425.5... -
Page 8: Exploded View
EXPLODED VIEW Model: A5/32, A7/32 Name Name Top cover Wires clip Column Wires clip Air side heat-exchanger Low pressure switch Motor bracket Handle Motor Controller Axial fan Needle valve Front panel Water flow switch Grille Titanium heat-exchanger Chassis E-box ass’y Compressor 21.1 Capacitor... - Page 9 Right panel Model: A10/32, A13/32 Name Name Top cover Fixing plate Cover, E-box Right panel Air side heat-exchanger Handle Motor bracket Low pressure switch Motor Controller Axial fan Titanium heat-exchanger Front panel Water flow switch Grille Needle valve Right panel, front E-box ass’y...
-
Page 10: Installation
Chassis 20.1 Capacitor Compressor 20.2 Capacitor INSTALLATION Installation information The following information given here is not an instruction, but simply meant to give the user a better understanding of the installation. Condition of installation The following information given here is not an instruction, but simply meant to give the user a better understanding of the installation. - Page 11 If your installation is equipped of the water treatment with product adductions (e.g. chlorine, brominates, salt…) the by-pass must be installed before the water treatment, with a non-return valve between the by-pass and water treatment. Electrical connection Electrical supply must correspond to that indicated on the appliance. ...
-
Page 12: Controller
swimming pool properly can considerably shorten this period. Time Delay - the appliance is fitted with built-in start-up delay of 3 minutes as protection for the electronics and to increase the life of the contacts. After this interval, the appliance will restart automatically. -
Page 13: Parameter Checking And Adustment
decrease; switch to the next parameter. Menu item 3. In the parameter setting interface, press this key to switch decrease the parameter value. Note: The system exits to the home screen if no key is pressed within 10s in the parameter query or setting interface. - Page 14 downtime (DT) delay before load is enabled T2 enable Enabling T2 sensor 0: Disable; 1: Enable T1 sensor calibration –9°C to +9°C 0°C T2 sensor calibration –9°C to +9°C 0°C T2LS T2 under-temperature value 3°C to 20°C 7°C Power failure Power failure memory validity 0: Invalid;...
-
Page 15: Wiring Diagram
Attention: The above codes can also be used to represent low voltage faults, because low voltage switches and temperature sensors are connected in series, this situation may be caused by refrigerant leakage. It is necessary to find professional maintenance personnel. WIRING DIAGRAM Please refer to the wiring diagram on the electric box. - Page 16 A10/32, A13/32 -15-...
-
Page 17: Specifications
SPECIFICATIONS Model A13/32 A5/32 A7/32 A10/32 Air temperature: 15°C DB/12°C WB, water inlet/outlet temperature: 26°C/28°C Heating capacity 3.30 4.80 7.10 9.13 Power input 0.71 1.06 1.48 1.96 4.65 4.53 4.80 4.66 Air temperature: 26°C DB/23.5°C WB, water inlet/outlet temperature: 26°C/28°C Heating capacity 4.50 6.60... -
Page 18: Maintenance
Water proof level IPX4 Notes: The specification may be changed for product improvement, please refer to the nameplate of product. MAINTENANCE To protect the paintwork, avoid leaning or putting objects on the device. External heat pump parts can be wiped with a damp cloth and domestic cleaner. (Attention: Never use cleaning agents containing sand, soda, acid or chloride as these can damage the surfaces.) To prevent faults due to sediments in the titanium heat exchanger of the heat pump, ensure that the heat exchanger cannot be contaminated (water treatment and filter system necessary). -
Page 19: Troubleshooting
Attention: The warranty does not cover damage caused by inadequate lay-up measures during the winter. TROUBLESHOOTING This section provides useful information for diagnosing and correcting certain troubles which may occur. Before starting the troubleshooting procedure, carry out a thorough visual inspection of the unit and look for obvious defects such as loose connections or defective wiring. - Page 20 Recycling ENVIRONMENTAL INFORMATION This equipment contains fluorinated greenhouse gases covered by the Kyoto Protocol. It should only be serviced or dismantled by professional trained personnel. This equipment contains R32 refrigerant in the amount as stated in the specification. Do not vent R32 into the atmosphere: R32, is a fluorinated greenhouse gas with a Global Warming Potential (GWP) = 675.
Need help?
Do you have a question about the 7024510 and is the answer not in the manual?
Questions and answers