Related Manuals for High Voltage VLF E Series
Summary of Contents for High Voltage VLF E Series
- Page 1 VLF E Series VLF hook up and control with E-Link The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc. • hvinc.com • p. 518.329.3275 • f. 518.329.3271 • 31 County Route 7A •...
- Page 2 Disclaimer This guide for the High Voltage, Inc. E Series of VLF hipots are meant to be for reference only. The instructions are intended to be clear and simple, but the operator must be trained and qualified according to the established procedures required for the use of this type of equipment.
- Page 3 E-Series VLF Hipot Hook Up VLF-34E VLF-65E The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc. • hvinc.com • p. 518.329.3275 • f. 518.329.3271 • 31 County Route 7A • Copake, NY 12516 USA...
- Page 4 VLF-34E Shown Station Neutral or Ground Low Side The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc. • hvinc.com •...
- Page 5 Step 2: Install High Voltage Output Cable Install shielded output cable, tighten ring lug until snug The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc. • hvinc.com • p. 518.329.3275 •...
- Page 6 Step 3: Connect To the Test Object Connect the Alligator Clip from the High Voltage Output Cable to cable or high side of device under test The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
- Page 7 3. Push down on the encoder or press the green button 4. Choose VLF-34E or VLF-65E (depending on model) 5. Push down on the encoder or press the green button The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
- Page 8 1. “Overload on Arc” to have VLF power down if failure occurs 2. “Burn on Arc” to have VLF condition fault if failure occurs 6. Press the blue button to start the test The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
- Page 9 Control of VLF and Tan Delta via E-Link with PC The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc. • hvinc.com • p. 518.329.3275 • f. 518.329.3271 • 31 County Route 7A •...
- Page 10 2. Install the drivers for the Xbee Antenna 3. Download via the Internet (or) 4. Download via the red or black HVI flash drive The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
- Page 11 5. Click the “Auto Detect” button 6. The software should automatically assign a serial port 7. Click “Close” 8. If you have issues please contact factory@hvinc.com The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
- Page 12 Step 8: Test Setup using the E-Link Software Click “Run Test” The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc. • hvinc.com • p. 518.329.3275 • f. 518.329.3271 • 31 County Route 7A •...
- Page 13 1. “Overload on Arc” to have VLF power down if failure occurs 2. “Burn on Arc” to have VLF condition fault if failure occurs 6. Click the green “Start” Button The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
- Page 14 Thank You from Thank you for viewing, if you have any questions please contact High Voltage, Inc. or your local High Voltage, Inc. Sales Representative The World’s Source for High Voltage Test Equipment ISO 9001 2008 MADE IN THE USA High Voltage, Inc.
Need help?
Do you have a question about the VLF E Series and is the answer not in the manual?
Questions and answers