Advertisement
Quick Links
ROLLNLOCK
2
EN
Pulley / rope clamp.
80 g
MADE IN ITALY
EN 12278:2007
EN 567:2013
B
C 0333
D
Regulation (EU) 2016/425
Personal Protective Equipment against falls from a height.
F
=
G
+
S
+
S
S
or
0
1
2
2.1
5
1
5.1
7
1
COMPATIBILITY.
1.1
UIAA
7.1
BBBB
For use with:
Ropes EN 892 / EN1891 Ø 8 ÷13 mm.
Webbing 10÷16 mm (Attention! Exceptional use, not
to be used for the protection against falls from a height).
1.2
Attention!
Not to be used
with cables!
7.3
NOMENCLATURE OF PARTS
1
A
8
13
C
UIAA
4
BBBB
33
6
E
30
7
G
34
11
H
12
2.2
2.3
HAULING PULLEY MODE
Install correctly the device and connect it to the anchor point. Before the use check that the
INSTALLATION
device operates correctly and the rope is in the right direction.
2
g
g
g
5.2
5.3
5.4 - CHECK
To switch from hauling pulley mode to simple pulley mode, move
SIMPLE PULLEY MODE
the sheave position lever until it engages the pin. It works as a
INSTALLATION AND USE
pulley.
UIAA
UIAA
BBBB
BBBB
7.2
g
UIAA
UIAA
BBBB
BBBB
g
7.4
7.5
3
ROPE CLAMP MODE
Raise the mobile side plate and turn 180° to open it out. Feed the rope through in the correct direction, then turn
INSTALLATION
the side plate to the closed position. Insert the connector in the hole and connect it to the harness.
31
T1
1
T8
T3
32
2
3.1
3.2
3.3
6
HAULING PULLEY MODE
INSTRUCTIONS FOR USE
STOP!
g
g
5.5 - OK!
5.6 - TESTING
6.1 - HAULING
8
SLING ADJUSTMENT MODE
INSTALLATION AND USE
OK!
OK!
SAFE WORKING
LOAD
5 kN
Exceptional use, not to be used
Exceptional use, not to be used
for the protection against falls
for the protection against falls
from a height!
from a height!
2,5 kN
2,5 kN
7.6
MAX
MAX
BREAKING LOAD
LOAD
LOAD
3 kN
3 kN
20 kN
10 kN
10 kN
7.7
8.1
3.4 - CHECK
3.5 - OK!
3.6 - TESTING
The device allows the rope to slide in one way and locks in the op-
posite. Ideal for hauling loads or rescuing persons.
STOP!
g
g
6.2 - HAULING
6.3 - LOCKING
NOT COVERED BY EN 567. In exceptional cases, the device can be employed for the length
adjustment of a lanyard or a daisy chain, connected to the harness by means of a knot.
NO!
NO!
8.2
8.3
4
ROPE CLAMP MODE
INSTRUCTIONS FOR USE
Ideal for ascending a rope. It can be used
also for short descents.
STOP!
4.1
STOP!
Max
4 kN
4.2
1
2
8.4
4.3
Advertisement
Related Manuals for Climbing Technology ROLLNLOCK
Summary of Contents for Climbing Technology ROLLNLOCK
- Page 1 ROLLNLOCK ROPE CLAMP MODE ROPE CLAMP MODE Raise the mobile side plate and turn 180° to open it out. Feed the rope through in the correct direction, then turn NOMENCLATURE OF PARTS INSTALLATION the side plate to the closed position. Insert the connector in the hole and connect it to the harness.
- Page 2 11) SLING ADJUSTMENT MODE. 1.1 - Intended uses. The equipment is designed for the following The Rollnlock can be employed for the length adjustment of a lan- applications: protection against falls from a height (EN 12278); pre- yard (Fig. 8.1) or a daisy chain (Fig. 8.2), connected to the harness vention of falls from a height and protection against moderate falls by means of a knot.
Need help?
Do you have a question about the ROLLNLOCK and is the answer not in the manual?
Questions and answers