Table of Contents
Advertisement
Quick Links
MODUL-AiR ERECTING INSTRUCTIONS
(V-1.10)
WE URGE YOU TO TAKE THE TIME TO STUDY THESE INSTRUCTIONS IN EVERY DETAIL!
** YOU MUST KEEP YOUR BOX WHILST YOUR AWNING IS UNDER WARRANTY **
This is a very large box which we have made especially for our AiR awnings.
You will struggle to find a similar box if you choose NOT to keep the original.
We will be unable to collect your awning whilst under warranty, if you do not keep this box.
Firstly, check the contents of each box within 7 days of receipt. If for any reason some items are
found to be missing then it's important we know which box they are missing from in order to send
you the correct quantity. A check list can be found at the end of this document. This is a good time
to familiarise yourself with the various component parts of your awning.
INSTRUCTIONS
We recommend that the draught cloth and wheel arch cover are fitted first. This helps to avoid
catching parts of the awning within the wheel arch or under the caravan. (NB. Grease, oil, tyre
dressing etc, cannot be removed from the canvas and is not covered by the warranty)
IMPORTANT
Ensure that all air valves are fully closed (diagram 1). This can be achieved by pressing
in the valve insert within the valves core with your finger or thumb and turning it clockwise. (Do not
use pliers or similar to do this, it will damage the valve and this would not be covered by our
warranty.) The valves are fitted to the bottom of each main AiR beam. (To test, push the insert
down with your finger and it should spring back up following your finger out of the valve.) See
below;
When inflating your new AiR awning, we recommend that for the first two or three times, you leave the dust
caps OFF the valves whilst inflating. Once you are happy that the awning is fully inflated, you can then replace
the dust caps. We recommend inflating using the centre valve on the 260 and 330 models or either of the
centre valves on the 390 model.
If whilst inflating the awning, any of the valves appear to be not fully closed, push in and out a couple of times
with your finger to rectify this.
VALVE CLOSED (Ready for inflation)
VALVE OPEN (Ready for deflation)
Diagram 1
Diagram 2
1 |
P a g e
Advertisement
Table of Contents
Summary of Contents for Bradcot MODUL-AiR
- Page 1 MODUL-AiR ERECTING INSTRUCTIONS (V-1.10) WE URGE YOU TO TAKE THE TIME TO STUDY THESE INSTRUCTIONS IN EVERY DETAIL! ** YOU MUST KEEP YOUR BOX WHILST YOUR AWNING IS UNDER WARRANTY ** This is a very large box which we have made especially for our AiR awnings.
- Page 2 Most caravans are fitted with “feed in” points at the base or at head height of the channel. The Modul-AiR allows for the right hand facing side panel to also fit into the caravan channel if required. This is a must if you are to use Modul-AiR as a “Full Awning”...
- Page 3 Assemble the two Easy Alloy “back poles” and fit the blanked end of the pole into the small black pocket on the “packer”, located down the side of the caravan. Ensure that the packer itself is lying flat against the caravan. The AiR tube must be fully into the top corner of the awning with the packer lying flat between the caravan and AiR tube and the Velcro strips art the very top attached.
- Page 4 (This removed side panel will then be re-fitted to the extension once the extension has been fitted to the main unit. If using Modul-AiR in a “full awning” configuration with a front closure unit, this side panel becomes redundant).
- Page 5 From inside the awning you will see that the extensions “cross beam” inflation tube is fitted with Velcro on the end. This should be attached to the opposing Velcro found on the side of the main inflation beams. The connection here can be re-adjusted at any time following inflation. Once all required extensions are in place, repeat the first part of the pegging process as you did on the main unit, re-inflate the main unit and then inflate each extension beginning with the extension closest to the main unit.
- Page 6 Please do not attempt to open any of the containment zips in the air beams at any time. There are no customer serviceable parts contained within those zips and opening them without an express written instruction from Bradcot will invalidate your guarantee. These zips are fitted with a “use once only” security tag and should not be removed.
- Page 7 Don’t: Clean the awning with any type of detergent. Don’t: Use any aerosol sprays on or near the canvas parts. Don’t: Use any awning “tie-down” kit, other than that available from Bradcot UK. These can be purchased via our website.
- Page 8 MODUL-AiR PACKING CHECK LIST (V-1.9) The following is a list of contents that should be found within the “MODUL-AiR” AWNING BOX. MAIN AWNING CANVAS PACK ⃝ GROUND PEG PACK (to include large and small pegs) ⃝ STORM STRAPS (Modul-AiR 260 and 330 x 3. Modul-AiR 390 x 4) ⃝...
Need help?
Do you have a question about the MODUL-AiR and is the answer not in the manual?
Questions and answers