Related Manuals for Control Techniques Nidec AFFINITY
Summary of Contents for Control Techniques Nidec AFFINITY
- Page 1 Macro Guide Affinity Model sizes 1 to 6 Building Automation HVAC/R drive Part Number: 0474-0010-02 Issue: 2...
- Page 2 When electronic products reach the end of their useful life, they must not be disposed of along with domestic waste but should be recycled by a specialist recycler of electronic equipment. Control Techniques products are designed to be easily dismantled into their major component parts for efficient recycling.
-
Page 3: Table Of Contents
Contents Safety Information .........4 Warnings, Cautions and Notes ......4 Important safety information. Hazards. Competence of designers and installers ....4 Responsibility ............4 Compliance with regulations .........4 Electrical hazards ..........4 Stored electrical charge ........4 Mechanical hazards ..........4 Access to equipment ..........4 Environmental limits ..........4 1.10 Hazardous environments ........4 1.11 Motor ..............5 1.12 Mechanical brake control ........5... -
Page 4: Safety Information
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Safety Information Electrical hazards The voltages used in the drive can cause severe electrical shock and/or Warnings, Cautions and Notes burns, and could be lethal. Extreme care is necessary at all times when working with or adjacent to the drive. -
Page 5: Motor
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults 1.11 Motor The safety of the motor under variable speed conditions must be ensured. To avoid the risk of physical injury, do not exceed the maximum specified speed of the motor. -
Page 6: Macros
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Macros Introduction A macro is a simple and easy way of pre-configuring the drive parameters for a specific application. The following set of core macros are pre-programmed in the Affinity SMARTCARD and can be loaded to the drive using a few simple steps. -
Page 7: Common Macro Parameters
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Common macro parameters Table 2-2 lists the menu 0 parameters that are common for all macros Table 2-2 Common Menu 0 parameters macros Range( ) Default( ) Parameter 0.00 xx.00... - Page 8 Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Range( ) Default( ) Parameter 0.43 Motor rated power factor {5.10} 0.000 to 1.000 0.850 200V drive: 230 400V drive: EUR> 400, USA> 460 0.44 Motor rated voltage {5.09} 0 to AC_VOLTAGE_SET_MAX V 575V drive: 575...
-
Page 9: Macros 6501/6502
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Macros 6501/6502 Optional 1. Minimum frequency reference – Pr 0.01. Overview 2. Maximum frequency reference – Pr 0.02. 3. Acceleration rate (sec/100Hz) – Pr 0.03. These macros set up the drive to control a fan or pump motor when 4. -
Page 10: Macros 6601/6602
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Macros 6601/6602 Optional 1. Minimum frequency reference – Pr 0.01. 2. Maximum frequency reference – Pr 0.02. Overview 3. Acceleration rate (sec/100Hz) – Pr 0.03. These macros set up the drive to control a fan or pump motor when 4. -
Page 11: Macros 6603/6604
Auto The EBC is supplied pre-wired as a three contactor bypass system along Input Contactor with an Affinity drive from Control Techniques. For questions about Bypass Contactor wiring schematics of the EBC to the drive, contact you local Control Output Conatctor Techniques drive center. -
Page 12: Sequence Of Operation
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Sequence of operation Auto mode To run in Auto mode: Close the Drive Enable signal (drive terminals 22 and 31). The status on the keypad changes from ‘inh’ to ‘rdy’ indicating that the drive is ready to 1. -
Page 13: Parameter Differences From Defaults
Parameter differences from Safety Information Macros Macros 6501/6502 Macros 6601/6602 Macros 6603/6604 defaults Parameter differences from defaults Table 6-1 Macro 6501/6502: Fan/Pump Control - No Bypass (Eur, 50 Hz) Macro Default( ) Parameter Default( ) Parameter Range( ) Pump 0.01 Minimum reference clamp {1.07} ±... - Page 14 0474-0010-02...
Need help?
Do you have a question about the Nidec AFFINITY and is the answer not in the manual?
Questions and answers