MPPT S3 Series Quick Start Manual

MPPT S3 Series Quick Start Manual

Solar charge controller v117

Advertisement

Quick Links

Reminder: For advanced function and application, please go to

Main Features

30A/40A/50A/60A MPPT solar charge controller
MPPT technology
Built-in DSP controller with high performance
Automatic battery voltage detection for 12V/24V/36V/48V
3-stage charging optimizes battery performance
The MPPT track speed is 5 times faster than traditional controllers
The charging voltage accuracy is ± 0.2V
Overcharge protection, Input PV polarity reverse protection, Output limited current protection, Over-temperature protection
Suitable for battery types such as sealed lead acid, vented gel and lithium battery, etc

Warning and Caution

Be aware that only qualified professionals could install these controllers. Please read full manual before installing
them.
1) The controllers can be installed indoor only. Keep controller away from water. Don't use wet towel to wipe controller.
2) Keep controller in an environmental temperature from -22℃~+55℃. Avoid direct sunlight.
3) Keep good heat dissipation.
4) Use the pure copper wires and connect all polarity correctly.
5) The output is only for DC load less 5A current. If your battery is 48V, then load should be 48V and current less 5A
6) Please don't set any parameters if you are not professional since the controller can work well on default except lithium
battery.
7) Please don't insert any meter or other devices between controller to battery and controller to PV.
8) Please use two-pole circuit breaker. And make sure input and output with separate circuit breakers.

PV Module Requirement

Models: S3-30A, S3-40A, S3-50A, S3-60A V117
Maximum PV Module Power
PV Module Open Circuit Voltage
(Voc of panel should be in the
correct range)
Notes: Voc is 1.5 or 2 times than battery voltage, then it's best efficiency. Please choose the PV modules with right Voc.
S3 SERIES MPPT SOLAR CHARGE CONTROLLER V117
For Models: S3-30A, S3-40A, S3-50A, S3-60A
For 12V Battery
For 24V Battery
For 36V Battery
For 48V Battery
For 12V Battery
For 24V Battery
For 36V Battery
For 48V Battery
S3-30A
S3-40A
≤400W
≤480W
≤720W
≤960W
≤1000W
≤1400W
≤1200W
≤1700W
DC20V~DC80V
DC37V~DC105V
DC50V~DC160V
DC72V~DC160V
www.makeskyblue.com
S3-50A
S3-60A
≤600W
≤720W
≤1200W
≤1440W
≤1800W
≤2100W
≤2200W
≤2800W

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S3 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for MPPT S3 Series

  • Page 1 Automatic battery voltage detection for 12V/24V/36V/48V 3-stage charging optimizes battery performance The MPPT track speed is 5 times faster than traditional controllers The charging voltage accuracy is ± 0.2V Overcharge protection, Input PV polarity reverse protection, Output limited current protection, Over-temperature protection...
  • Page 2 Circuit breaker 63Ax2PCS 63Ax2PCS 63Ax2PCS 100Ax2PCS MakeSkyBlue MPPT SOLAR CHARGE CONTROLLER Circuit breaker Circuit breaker DC Load Battery Installation steps 1. Take one two-pole circuit breaker and keep it turn off, then install this circuit breaker between controller and battery, then connect batteries to controller with correct polarity.
  • Page 3 Basic Parameter Models S3-30A S3-40A S3-50A S3-60A Charging mode 3-stage: constant current(MPPT), constant voltage, floating Battery voltage automatic recognition: 12V Battery DC9V~DC15V Battery voltage automatic recognition: 24V Battery DC18V~DC29V Battery voltage automatic recognition: 36V Battery DC30V~DC39V Battery voltage automatic recognition: 48V Battery...
  • Page 4 Step 3: D02 Continue to press the button UP, LCD shows 14.5 (Voltage can be set from 12V-17V). This is highest absorption voltage for battery. Press ENT until numbers flash, then long-press UP/DOWN to set up voltage that you want, press ENT to confirm it.

This manual is also suitable for:

S3-30aS3-40aS3-50aS3-60a

Table of Contents