Download Print this page
Sealey LED438 Instructions

Sealey LED438 Instructions

Rechargeable spotlight 10w cree led

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Manual
1. SAFETY
1.1.
GENERAL
Ensure the lamp is fully charged before initial use.

DO NOT turn the lamp on when it is being charged.

DO NOT shine directly into your, another person's or an animal's eyes.

DO NOT allow children to use the lamp.

DO NOT handle or move the lamp whilst it is being charged.

DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.

DO NOT leave battery in a discharged state, recharge battery immediately. Before storage; fully recharge the battery, subsequently

recharge the battery at least once every six months if out of use.
1.2.
ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING LAMP TO THE POWER SUPPLY.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:
R
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical
supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
You must ensure that you inspect the charger plug, cable and connector for wear and damage to ensure items are safe before
connecting to the mains power supply.
1.2.1.
If worn or damaged DO NOT use.
IMPORTANT: Check that the voltage marked on the charger plug is the same as the lamp.
V
1.2.2.
Uncoil the cable between charger and the lamp.
DO NOT pull the charger plug from the mains socket by the lead.

WARNING! DO NOT use any other type of charger with this product, other than the supplied mains or car charger. Failure to observe
R
this warning could result in injury and or fire and will invalidate the warranty.
DO NOT try to take the charger plug apart.

DO NOT use the charger plug to charge or power any other electrical item.

DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).

1.3.
BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
R
DO NOT attempt to open, dismantle, modify or service the battery pack.

DO NOT crush, puncture, short external contacts or dispose of in fire or water.

DO NOT expose to temperatures above 60°C (140°).

Replace only with the battery pack designated for this product.
Recycle or dispose of used battery as stipulated by local regulation.
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
Weatherproof composite case with swivel handle feature allowing pistol grip or carry handle operation. Integral adjustable foot doubles up as
carry handle when used in pistol grip mode. Ø125mm lens with super bright 10W XM-L CREE LED spotlight. Two modes of brightness, 850 and
280 lumens, lasting up to 9 hours on standard, and an emergency amber flashing rear light that can last up to 100 hours. Powered by a 3.7V
4Ah Li-ion battery. Supplied with mains and in-car charger.
© Jack Sealey Limited
INSTRUCTIONS FOR:
RECHARGEABLE SPOTLIGHT 10W CREE LED
LED438
MODEL NO:
Original Language Version
LED438
Issue:2(D) - 18/11/16

Advertisement

loading

Summary of Contents for Sealey LED438

  • Page 1 LED438 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and maintained properly, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Remove the 2 screws holding the amber lens and remove it. Disconnect the wiring from the circuit board. Remove the battery. Dispose of according to local government guidelines. Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.