Magnetek SBP2 Installation Instructions Manual page 7

12 Parts List
Description
Two-Button On/Off
Two-Button All Single-Speed
Two-Button
Two-Button All Two-Speed
Two-Button All Three-Speed
Four-Button (2) Single-Speed with On/Off
Four-Button (2) Two-Speed with On/Off
Four-Button Four-Button All Single-Speed
Four-Button All Two-Speed
Four-Button All Three-Speed
Six-Button (4) Single-Speed with On/Off
Six-Button (4) Two-Speed with On/Off
Six-Button (4) Three-Speed with On/Off
Six-Button
Six-Button All Single-Speed
Six-Button All Two-Speed
Six-Button All Three-Speed
Eight-Button (6) Single-Speed with On/Off
Eight-Button (6) Two-Speed with On/Off
Eight-Button (6) Three-Speed with On/Off
Eight-Button
Eight-Button All Single-Speed
Eight-Button All Two-Speed
Eight-Button All Three-Speed
Ten-Button (8) Single-Speed with On/Off
Ten-Button (8) Two-Speed with On/Off
Ten-Button (8) Three-Speed with On/Off
Ten-Button
Ten-Button All Single-Speed
Ten-Button All Two-Speed
Ten-Button All Three-Speed
Twelve-Button (10) Single-Speed with On/Off
Twelve-Button (10) Two-Speed with On/Off
Twelve-Button (10) Three-Speed with On/Off
Twelve-Button
Twelve-Button All Single-Speed
Twelve-Button All Two-Speed
Twelve-Button All Three-Speed
Catalog #
SBP2-2-WB
SBP2-2-WA
SBP2-2-WS
SBP2-2-WT
SBP2-4-WB
SBP2-4-WBS
SBP2-4-WA
SBP2-4-WS
SBP2-4-WT
SBP2-6-WB
SBP2-6-WBS
SBP2-6-WBT
SBP2-6-WA
SBP2-6-WS
SBP2-6-WT
SBP2-8-WB
SBP2-8-WBS
SBP2-8-WBT
SBP2-8-WA
SBP2-8-WS
SBP2-8-WT
SBP2-10-WB
SBP2-10-WBS
SBP2-10-WBT
SBP2-10-WA
SBP2-10-WS
SBP2-10-WT
SBP2-12-WB
SBP2-12-WBS
SBP2-12-WBT
SBP2-12-WA
SBP2-12-WS
SBP2-12-WT
SBP2 Pendant Pushbutton Stations Installation Instructions
Page 22 of 26
NOTICE indicates a potential equipment damage message.
Do not operate the SBP2 Pendant Pushbutton Station unless you are fully
trained and qualified to operate the overhead material handling system of
which this SBP2 is a component. For applications other than overhead
cranes or hoists, consult Electromotive Systems at 1-800-288-8178.
Read the entire contents of this manual before you install or use the SBP2
Pendant Pushbutton Station.
If the pendant cable grip is not properly sized to fit the pendant cable,
contamination of the pendant housing is possible. Contaminants that enter
the switch contacts may result in a potentially unsafe operating condition.
When cutting, stripping and installing wires, ensure that contaminants do not
fall into the enclosure. Contaminants that enter the switch contacts may result
in a potentially unsafe operating condition.
Some pendant cable manufacturers add talc to their cable during the
manufacturing process. This talc can migrate from the cable into the housing
of the pendant station. As a result, the contamination of the switch contacts
may occur, resulting in a potentially unsafe operating condition. Electromotive
Systems therefore recommends only the use of talc-free cable for the wiring
of all pendant stations.
Remove all contaminants from the housing and switch contact areas prior to
sealing the enclosure and putting the pendant into service.
Prior to the installation, inspection, or repair of the pendant station,
disconnect power at the source following the lockout/tagout procedures as
outlined in ANSI Z244.1.
June 2020
NOTICE
NOTE: A NOTE statement is used to notify people of installation,
operation, programming, or maintenance information that is important,
but not hazard-related.
WARNING
WARNING
CAUTION
SBP2 Pendant Pushbutton Stations Installation Instructions
June 2020
Page 7 of 26