Page 1
VT/VLT Series Low Temperature Freezers User Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS Write Model and Serial Numbers here: Accucold Division of Felix Storch, Inc. Model: _____________________ An ISO 9001:2015 registered company Serial No.: __________________ 770 Garrison Avenue Bronx, NY 10474 www.accucold.com...
TABLE OF CONTENTS Appliance Safety Important Safeguards Installation Instructions Locating your Appliance Leveling your Appliance Grounding your Appliance Key Eject Lock Reversing the Door Swing Operating your Appliance Setting the Temperature 8-10 For Dial Thermostats For Digital Thermostats Traceable Thermometer Alarm Keypad Lock Energy-Saving Tips Operating Specific Models...
APPLIANCE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your unit. Always read and obey all safety messages. This is the Safety Alert Symbol. The symbol alerts you to potential hazards that can kill or injure you and others.
Page 4
Air the room in which the unit isolated for several minutes, and Contact the Service Department for advice. • The more coolant there is in a unit, the larger the room it should be installed in. In the event of a leakage, if the unit is in a small room, there is the danger of combustible gases building up.
INSTALLATION INSTRUCTIONS Use two or more people to move and install your appliance. Failure to do so can result in back or other injury. CAUTION: YOU MUST ALLOW THE APPLIANCE TO SIT UPRIGHT FOR 24 HOURS BEFORE TURNING ON, TO ALLOW THE COMPRESSOR LUBRICANT TO DRAIN. Failure to do so may adversely affect the performance and the lifetime of the unit.
Grounding your Appliance A 115 Volt (AC only) 60 Hz grounded electrical supply with a 15- or 20- amp fuse or circuit breaker is required. It is recommended that a separate circuit serving only your appliance be provided. Use outlets that cannot be turned off by a switch or pull chain. Do not use an extension cord. Key Eject Lock Some models have factory-installed lock to secure the contents of the unit.
OPERATING YOUR APPLIANCE In order to ensure proper temperature, you need to permit proper airflow in the appliance. Do not block any air vents. If the vents are blocked, airflow will be prevented, and temperature and moisture problems may occur. Always position contents to allow some airflow between shelves or baskets. Allow the appliance to cool at least 6 to 8 hours before adding contents.
SETTING THE TEMPERATURE For Dial Thermostats Your appliance may be controlled with a thermostat knob located inside the unit, towards the right-hand corner. Turn the knob clockwise from the STOP (0) position toward the higher numbers for colder temperatures. • Higher settings on the knob (higher numbers) mean lower temperatures (colder) in all compartments of the appliance.
Traceable Thermometer/Alarm Some units are equipped with a Traceable Thermometer/ Alarm that simultaneously displays minimum, maximum, and current interior temperatures and provides a visual and audible signal when the temperature inside the unit falls outside the set temperature range. The temperature sensor, or probe, is enclosed in a glycol-filled bottle that you insert into the location to be monitored, such as inside a refrigerator or freezer, once the unit has been programmed.
Keypad Lock (Optional on Most Models) The factory-set default password is 0123. If the default password is lost, press the (located inside the battery box) for 30 seconds, then wait for the warning sound, which signifies the factory-set default password has been restored. Setting the Password While door is open, press the key (located inside the battery box) until it jingles, enter the...
OPERATING SPECIFIC MODELS NOTE: Models with BI in the model number, or VT65/VLT650 models, are designed for built-in operation and need only minimal clearance on the sides and above the units. All other models require 4 inches of airflow on the sides and above the units. All models operate best when 2 inches is provided between the rear wall and the back of the unit.
CLEANING AND CARE Cleaning a Frost-Free Appliance (including models starting with EQFF and EQFR) Frost-free means that you do not have to defrost your appliance. Frost is removed by air moving and collecting any moisture and depositing it on the cooling coil. The cooling coil periodically warms up enough to melt the frost, and the water then flows down to the drain pan (located behind the base grill) where it is evaporated.
If you need to order replacement parts, we recommend that you only use factory-specified parts. Factory-specified parts will fit right and work right because they are made with the same precision used to build all Accucold equipment. Call customer service toll free in the USA: 1-888-4-MEDLAB Monday to Friday 9:00 a.m.
TROUBLESHOOTING If you notice a problem with your appliance, try these solutions first to avoid the cost of an unnecessary service call. Problem Possible Solution The appliance will not operate. Replace the fuse or reset the circuit breaker. Recheck to see whether the unit is operating in 30 minutes.
For more information go to www.P65Warnings.ca.gov Note: Nickel is a component in all stainless steel and some other metal components. Accucold Division of Felix Storch, Inc. For parts and accessory ordering, An ISO 9001:2015 registered company troubleshooting and helpful hints, visit: 770 Garrison Avenue www.accucold.com/support...
Need help?
Do you have a question about the EQFR Series and is the answer not in the manual?
Questions and answers