Advertisement
Quick Links
Advertisement
Related Manuals for Power Apex
Summary of Contents for Power Apex
- Page 1 Power Apex Product Instructions...
-
Page 2: Before You Start
We also strongly advise you to wear safety glasses when installing the felt to protect your eyes. Power Sheds Ltd cannot be held responsible for any damage or injury sustained due to incorrect unloading, unpacking, or assembly of any of our products. - Page 3 If you have not chosen to purchase our Power Base then other suitable bases would include a concrete base (75mm of concrete on top of 75mm of hardcore) or a paving slab base (slabs laid on...
-
Page 4: Component Checklist
Component checklist Window 2ft Roof Roof 2ft Roof Panel Door Panel Blank Panel Roof Panel 4ft Gable 6ft Gable 4x6 Floor Blank Panel (for Panel (for (or additional (may be double Floor Floor Floor Panel (for 4ft (for 6ft wide) blank panels if Panel doors) - Page 5 Bargeboard Bargeboard Diamond 1790mm heavy 1190mm heavy 4ft Truss 6ft Truss (for 4ft) (for 6ft) Finial duty bearer duty bearer Cover lat Felt Fixing pack 8ft Piece 12ft Piece 16ft Piece 10x4 20ft Piece 12x4 24ft Piece 14x4 (2x) 14ft Piece 16x4 (2x) 16ft Piece 18x4...
-
Page 6: Pre-Assembly
Clout nails (for the felt) 40mm galvanised nails If you have ordered a Power Base, you will also receive 80mm screws Pre Assembly 1. Safely unpack your components and check that you have all the parts required. Please use the table in the two previous few pages to view which components are required for the size you have ordered. - Page 7 For floors over 12ft long this method should be followed but to do it in two halves. USEFUL TIP! – If you have purchased a POWER Base you can screw the floor to the timber POWER base below for maximum strength and security.
- Page 8 Door 1. Your shed will either come with a single door or a double door depending on what you selected when ordering. Double doors are already hung on the door panel. However, for a single door you will need to hang the door. For a single door you can choose which way round to hang it –...
- Page 9 4. If your Power shed is 6ft wide (4x6, 6x6, 8x6, 10x6, 12x6, 14x6, 16x6, 18x6, 20x6) then you will need to position one of the 2ft blank panels next to the 4ft wall panel you have chosen to complete the 6ft gable end.
- Page 10 7. When you have secured all the wall panels (door panel, 2ft and 4ft blank panels, window panels) you then need to secure these to the floor using 70mm screws provided. Screw approximately into the floor with 2x screws for every wall panel (internally) ensuring the screws are driven through the framing at the bottom of the side/gable walls, through the floor boards and into the floor joists.
- Page 11 Gable Tops 1. Line up the gable tops with the panels at the gable ends (the ends where you attached the ‘heavy duty bearers’). 2. Secure them to the wall panels with 50mm screws from the inside, screwing upwards through the framing.
- Page 12 1302mm roof panels will mean there is an overhang at each end (except on the 4x4 and 4x6 Power Apex where there is no roof overhang). The only time the roof panels won’t line up with the truss and join in side walls is if you have positioned a 2ft side wall panel at one end –...
- Page 13 (note – there will be no roof overhang at the gable end on the 4x4 or 4x6 Power Apex). Then, screw the roof panels to the side wall panels with 50mm screws (ensuring you screw down in to every upright piece of framing on the side walls) and screw the roof panels into the gables at each end with 35mm screws (4x screws for each gable) 7.
- Page 14 4. Fold the overhanging felt at the gable ends under the roof boards and tack into place. Note - The 4x4 and 4x6 Power Apex roof panels will finish flush with the gables and so the felt will not tuck...
-
Page 15: Finishing Touches
1. Using the 40mm galvanised nails, fit the bargeboards to the roof panels and secure the diamond finials over the top of the bargeboards. 2. Secure corner strips at each corner of your Power shed with 40mm nails (at least four per strip). Extra strips are provided to cover any joins between side wall panels. - Page 16 Power Base Installation Instructions 1. The Power Base will be made up from the pressure treated timbers in the pack (this is the 100mm x 50mm timber). Note – for any time you screw some timber together, we suggest that you pre-drill the timber with a 3mm drill bit before inserting the screws.
- Page 17 Take extra care to brush treatment into all wooden components inside and outside. Feel free to change the colour of the building giving you the ‘power’ to style it your own way. Check your base Although your base should be level at the time of assembly, some bases can move over time and if you find this occurs then the building can twist or door may not close properly.
- Page 18 Returns If Power is not for you and you’d like to return your shed within 14 days of delivery then we will collect the item from you without charging a collection fee. No fuss, no fees! All we ask is that you do not unpack the shed or take the shed off the pallet. You will be able to see the shed panels on the pallet if you want to double check the quality of the shed panels.
Need help?
Do you have a question about the Apex and is the answer not in the manual?
Questions and answers