Uniz IBEE User Manual
  1. Manuals
  2. Brands
  3. Uniz Manuals
  4. 3D Printers
  5. IBEE
  6. User manual

Uniz IBEE User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IBEE and is the answer not in the manual?

Questions and answers

Related Manuals for Uniz IBEE

Summary of Contents for Uniz IBEE

  • Page 2 UNIZ; d) to damage caused by service (including upgrades and expansions) performed by anyone who is not a representative of UNIZ; e) to a Hardware Product or part that has been modified to alter functionality or capability without the written permission of UNIZ; f) to consumable parts, unless damage has occurred due to a defect in materials or workmanship;...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS A IBEE 3D PRINTER ..............1 MEET THE PRINTER ........................1 SPECIFICATIONS ..........................3 B GET STARTED ................. 4 UNBOXING ........................... 4 SOFTWARE PREPARATION ......................6 C INTERFACE INFORMATION ............. 7 MAIN INTERFACE .......................... 7 SETTINGS ............................7 TOOLS ............................

  • Page 4: A Ibee 3D Printer

    A IBEE 3D PRINTER This user manual is designed to help you start your IBEE printer experience. Learn everything about using your 3d printer by following the instructions in this user manual and experience how easy it is to produce great quality prints.
  • Page 5 A IBEE 3D PRINTER...

  • Page 6: Specifications

    16GB RAM, OpenGL 2.1, Discrete Graphics DESKTOP Built-in advanced model repair, Advanced Features SOFTWARE Ultra large file support (1GB+) Compatible Format STL, OBJ, AMF, 3MF, SLC Slice Format zcode * Maximum accuracy only achievable at integer multiples of smallest pixel sizes. A IBEE 3D PRINTER...

  • Page 7: B Get Started

    B GET STARTED Now your IBEE printer has arrived and you’re ready to unpack it and set it up! Carefully unpack your printer and set it up according to the following instructions. Please keep the original box and protectors in case of future shipping or storing.
  • Page 8 B GET STARTED...

  • Page 9: Software Preparation

    1. Double click the installation program. 2. Check the user agreement, and then follow the prompts to finish the installation. UNIZ Maker supports Mac OS X 10.7 and above. Please use the following steps: 1. Double click the installation program.

  • Page 10: C Interface Information

    C INTERFACE INFORMATION You may check device information, control the printer, and start printing projects using the touch screen on the front of IBEE. MAIN INTERFACE There are three main functions: Settings/Tools/Print. Note: Some functions have 1~3 pages to introduce the details. Please read carefully and follow the instructions.

  • Page 11: Tools

    UPGRATE OR RESET You can read or scan to get the SN of your printer here. LOGIN ACCOUNT Login an account to register your printer to UNIZ cloud. Then you can monitor the printer remotely. TOOLS LCD TEST Click LCD TEST you will see the UNIZ Logo appears on the LCD screen.
  • Page 12 EXPOSURE TO CLEAN When a failed print occurs and there are some residues left in the bottom of Resin Tank, you need to exposure to clean it. After that, please wear nitrile gloves and take the solidified piece out. RESET Z-AXIS ZERO POSITION AND LEVELING BUILD PLATFORM If you change for a new Build Platform or the printing model may not stick onto the Platform, please reset z-axis zero position and leveling the Build platform.

  • Page 13: Print

    MOTOR CONTROL If you want to control Build Platform to move upwards, choose a distance (10/30/50mm) first, and then click the arrow. Please do not click too fast and take an eye to watch the distance between Platform and top position. There is a scaleplate lable on the Z-axis frame for reference. PRINT PRINT WITH USB DISK Choose and click the slice you want to print, then the printer will step into normal printing...

  • Page 14: More Details

    In this interface, you may check the preview and printing parameters of the print. Also you may pause/resume or stop the printing program by click the buttons on left. PRINT RECALL The last file printed on the printer will be shown in the MOST RECENT interface. You may print a model second time very expediently with this function.
  • Page 15 2. While the printer is connected with internet through Wi-Fi, the icon on the right-up side will turn to highlighted state. 3. Please use your fingernail or any other hard thing to click the touch screen, especially in the keyboard interface. C INTERFACE INFORMATION...

  • Page 16: D Usage And Maintenance

    D USAGE AND MAINTENANCE In order to have a smoothly working IBEE printer, it is important to maintain it correctly. In this chapter the most important tips are described. It is recommended to read them carefully in order to achieve the best results with your printer.
  • Page 17 2. Install or remove the platform. SANDING BUILD PLATFORM After the platform has been used for a long time, its surface will become smooth which leads to poor model adhesion and increases the printing failure rate. To deal with this problem, users need to sand the platform.
  • Page 18 3. Clean the platform with alcohol again to make sure there is no residue left. RESET Z-axis ZERO POSITION AND LEVELING BUILD PLATFORM 1. Prepare one A4 paper and the Hexagon Wrench in the accessory box sent with printer. 2. Make sure the bottom of Platform is clean and dry. 3.
  • Page 19 4. Loosen the four screws with Hexagon Wrench by turning counter-clockwise. 5. Click TOOLS/ZERO&LEVELING, then read the introduction and click CONFIRM twice to start. 6. After Build Platform moves to the lowest position and stops, press the plate and tighten the four screws with Hexagon Wrench by turning clockwise-as the picture shows.
  • Page 20 7. Click CONFIRM to finish. D USAGE AND MAINTENANCE...
  • Page 21 8. Click TOOLS/MOTOR CONTROL, and then choose the 10mm option and click the arrow. Build Platform will move upwards. 9. Wait until the Platform stops, put a piece of A4 paper under the Platform and repeat step 5. 10. Try to pull out A4 paper from any directions. If you can feel the frictional force between Platform and A4 paper, that means it is zeroed and leveled successfully.

  • Page 22: Resin Tank

    CLEAN BUILD PLATFORM When printing fails, there may be residues on the platform which needs to be cleaned in time to avoid damage to the screen. Please use the Shovel delivered with the printer to remove the residues (please dispose of solidified materials and waste resin properly).
  • Page 23 2. Put Resin Tank onto the LCD screen. 3. Turn the four lock blocks to lock the Resin Tank. 4. Make sure the Resin Tank is stably locked and repeat the above steps if it shakes. CLEAN RESIN TANK When printing fails, there may be residues in the Resin Tank which needs to be cleaned in time to avoid damage to the screen.
  • Page 24 2. After the exposure is done, gently scrape off the whole piece of cured resin from Tank with a paper card. DO NOT use the scrapper, since this may damage the film and cause a severe leak. Change the Resin Tank Film 1.
  • Page 25 3. Take out the Film Frame, and put it on the table then remove the remaining 18 up-side screws. 4. Wipe clean the Resin Tank and Film Frame. Be careful don’t damage the film sealer. 5. Lay the Frame flat, sandwich a new film between the Frames, then press the film with the Acrylic Plate and Build Platform.
  • Page 26 6. Tighten the 18 up-side screws while holding the Film Frame down. 7. Put the Frame back into Resin Tank’s slot, then slowly tighten 16 down-side screws. 8. Changing the Resin Tank film is finished. D USAGE AND MAINTENANCE...

  • Page 27: Change Lcd Protective Film

    CHANGE LCD PROTECTIVE FILM There is a protective film on the LCD of IBEE. If the film is scratched or dirty with cured resin, you should change for a new one. 1. Peel off the old film. 2. Clean the surface of LCD and make sure there is no dust and residue left.
  • Page 28 5. Using a card and cloth to paste the film onto the surface of LCD. 6. Peel off the cover film marked ‘②’. 7. All done. The air bubble between film and LCD will disappear automatically in a period of time. D USAGE AND MAINTENANCE...

  • Page 29: Clean Air Filter

    CLEAN AIR FILTER 1. Pry and take off the cover of air filter at the behind of printer. 2. Take off the filter and use water or alcohol to clean it. 3. Push the filter and cover back. D USAGE AND MAINTENANCE...

  • Page 30: E Contact Us

    STORE uniz.com/store To learn about other UNIZ products, including UNIZ resins, please visit our online store. sales@uniz.com If you have additional questions about any UNIZ product, please email our Sales Team at the address above. FEEDBACK thoughts@uniz.com We love to hear from you. Please give us feedback.
  • Page 31 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. UNIZ Technology LLC 9400 Activity Rd Ste L, San Diego, California, 92126, United States...

Table of Contents