Related Manuals for LITTLE BEAVER Hydraulic Earth Drill
Summary of Contents for LITTLE BEAVER Hydraulic Earth Drill
- Page 1 Hydraulic Earth Drills OPERATORS MANUAL WITH MAINTENANCE AND PARTS INFORMATION www.LittleBeaverStore.com | (800) 878-7829 | Sales@LittleBeaverStore.com...
- Page 2 MACHINE SERIAL NUMBER There are two serial numbers for your hydraulic earth drill, one for the handle and one for the power source. The handle serial number is located on the bottom side of the handle. The power source serial number is located on the rear side of the hydraulic reservoir.
- Page 3 TABLE OF CONTENTS OPERATORS MANUAL Page # Safety Alert, Warranty and Machine Information Table of Contents Safety Instructions and Specifications Maintenance and Lubrication Instructions Wheel and Torque Tube Assembly O-6 & 7 Operating Instructions Handle and Auger Operation Information Extension and Accessories Decal Location Troubleshooting PARTS MANUAL...
- Page 4 400 ft.-lbs. If greater torque is required, please consult factory. LITTLE BEAVER, INC. reserves the right to make changes in design and changes for improvements upon its product without imposing any obligation upon itself to install the same upon its products theretofore manufactured.
- Page 5 MAINTENANCE AND LUBRICATION INSTRUCTIONS NOTE: All engines and hydraulic reservoirs are shipped WITHOUT oil. ENGINE: The engine is shipped without oil or gasoline. Refer to the manufacturers instructions for proper procedures and recommended fluid. HYDRAULIC FLUID AND FILTER: The hydraulic reservoir should be filled to the top of the sight gauge with hydraulic oil before attempting to start the engine.
- Page 6 WHEEL ASSEMBLY Attach a wheel to each end of the rear axle using a 3/4" flat washer and securing with a 1/8" x 1" cotter key. Attach the front wheel to the swivel bracket using one 3/4" x 5-1/2" cap screw, two spacers, and one 3/4"...
- Page 7 AFTER THE ENGINE HAS WARMED UP, Insert the auger into the drive adaptor on the bottom of the handle. Make sure the snap button and hole provided in the adaptor are aligned and the button snaps securely into place. Hold the handle so your left index finger and thumb can operate the throttle (pull with the index finger for forward rotation, push with the thumb for reverse).
- Page 8 FIGURE 6 ATTACHMENTS: Several attachments are available for your LITTLE BEAVER Earth Drill; including both west and dry type horizontal boring kits and a drill chuck adaptor which allows you to use a wood bit. Refer to the specific operating instructions supplied with the attachment. If these become lost or misplaced, replacements may be obtained from the factory.
- Page 9 DECAL LOCATION For Decal Kit, Order Part # 30181-D# Page O-8 1110 www.LittleBeaverStore.com | (800) 878-7829 | Sales@LittleBeaverStore.com...
- Page 10 Auger turns but will not dig 1) Foreign matter collected around point 2) Point or blade is dull 3) Wrong blade type for soil condition. Contact your dealer or factory for Little Beaver carbide blade Auger with extension will 1) Auger or extension bent or running out of line...
- Page 11 TANK AND CARRIER ASSEMBLY - 15 - 16 - 17 20 - ------32 ------33 - 10 - 28 - 18 25 - 27 - - 34 - 11 - 24 - 37 - 16 - 14 - 21 19 - - 23 - 22 Page P-1...
- Page 12 ITEM PART # DESCRIPTION WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the following maximum hose assembly lengths. Longer hose assemblies may allow the torque tube to uncouple, causing serious personal injury. 30100 Pressure Hose - 74 1/4" max. overall length 30111 Return Hose - 68"...
- Page 13 PUMP, FILTER AND SIGHT GAUGE ASSEMBLIES 10 - 12 - Inside Tank Tank Wall 21 / 24 - ITEM PART # DESCRIPTION 30260 Cap & Strainer Assembly 30262 Sight Guage Assembly 30172 Coupling Guard Assembly 3012-2 Screw - Guard 3/8" x 1" 3012-3 Lock Washer - Guard 3/8"...
- Page 14 TORQUE TUBE ASSEMBLY ITEM PART # DESCRIPTION 9058-1 Button Shield 9092-M One piece Torque Tube 9058 Spring & Button 9084-1 Spacer 30200 Kill Switch Wire (BIC) 30200-HW Kill Switch Wire (Honda & Wisconsin) 3007-5 Plastic Tie 30201 Wire Loom Page P-4 www.LittleBeaverStore.com | (800) 878-7829 | Sales@LittleBeaverStore.com...
- Page 15 ONE-MAN HANDLE 12 - - 20 26 - 14 - - 17 13 - - 28 - 18 - 27 10 - - 15 - 16 22 - 21 - - 25 23-- 30-- 11-- 31-- 24-- Page P-5 1101 www.LittleBeaverStore.com | (800) 878-7829 | Sales@LittleBeaverStore.com...
- Page 16 ONE-MAN HANDLE ITEM PART # DESCRIPTION WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the following maximum hose assembly lengths. Longer hose assemblies may allow the torque tube to uncouple, causing serious personal injury. 30102-A Hose-Valve to Power/Valve to Return, 36"...
- Page 17 TWO-MAN HANDLE 16 - - 18 24 - - 16 - 31 - 27 13 - - 14 - 15 11 - - 28 20 - 19 - 17 - 21-- - 34 - 10 - - 35 - 29 Page P-7 1101 www.LittleBeaverStore.com | (800) 878-7829 | Sales@LittleBeaverStore.com...
- Page 18 TWO-MAN HANDLE WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the following maximum hose assembly lengths. Longer hose assemblies may allow the torque tube to uncouple, causing serious personal injury. ITEM PART # DESCRIPTION 30102-A Hose-Valve to Power/Valve to Return, 36"...
- Page 19 ANCHOR HANDLE 12 - - 20 14 - 26 - 13 - - 17 - 28 - 18 - 27 10 - - 15 - 16 22 - 21 - - 25 23-- 30-- 11-- 31-- 24-- Page P-9 1101 www.LittleBeaverStore.com | (800) 878-7829 | Sales@LittleBeaverStore.com...
- Page 20 ANCHOR HANDLE ITEM PART # DESCRIPTION WARNING: For power source serial numbers from H-0001 through H-3252, do not exceed the following maximum hose assembly lengths. Longer hose assemblies may allow the torque tube to uncouple, causing serious personal injury. 30102-A Hose-Valve to Power/Valve to Return, 36"...
- Page 21 AUGERS & ACCESSORIES ITEM PART# DESCRIPTION 1.5X42-SSS 1-1/2" X 42" Auger, Snap-on with Screw-on Point 2.5X42B 2-1/2" X 42" Bucket Auger, Snap-on STANDARD AUGER 2.5X42SP 2-1/2" x 42" Spiral Barrel Auger (Soil Sampling) 2X36-SSS 2" X 36" Auger, Snap-on with Screw-on Point 2X42-SSS 2"...
- Page 22 ITEM PART# DESCRIPTION STANDARD AUGER 9023-C1.5 Blade, Screw-on, w/Carbide for 1-1/2" Augers WITH CARBIDE POINT 9023-C2 Blade, Screw-on, w/Carbide for 2: Augers 9023-C3 Blade w/Carbide for 3" Auger, Inc. Mtng. Bolts/Nuts 9023-C4 Blade w/Carbide for 4" Auger, " " " 9023-C5 Blade w/Carbide for 5"...
- Page 23 ITEM PART# DESCRIPTION EXTENSION ---4 9054 36" Tube Type Snap-on Extension 13-- 9054-A 18" Tube Type Snap-on Extension 9054-S1.5X36 1-1/2" x 36" Screw-on Ext.(Must use Screw-on Agr) 9054-S2X36 2" x 36" Screw-on Ext.(Must use Screw-on Auger) 9054-S3X36 3" x 36" Screw-on Ext.(Must use Screw-on Auger) 9054-3X36 3"...
- Page 24 IMPORTANT: All nuts, fasteners, and fittings must be kept tightened. Refer to torque chart for proper assembly torque. TORQUE INFORMATION HEX HEAD SOCKET TYPE WRENCH SIZE WRENCH SIZE GRADE GRADE inch SIZE No. 4 8 in lb 12 in lb 1/4"...
- Page 25 T T T T T H H H H H I I I I I N N N N N K K K K K S S S S S AFET AFET AFET Y Y Y Y Y AFET AFET FI FI FI FI FI RST! RST! RST!
Need help?
Do you have a question about the Hydraulic Earth Drill and is the answer not in the manual?
Questions and answers