DSC Power 832 Installation Manual
  1. Manuals
  2. Brands
  3. DSC Manuals
  4. Security System
  5. Power 832
  6. Installation manual

DSC Power 832 Installation Manual

Hide thumbs Also See for Power 832:

Advertisement

Table of Contents

Installation
Manual
PC51O8L v1.O
Please refer to the System Installation Manual for information on
limitations regarding product use and function and information
on the limitations as to liability of the manufacturer.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Power 832 and is the answer not in the manual?

Questions and answers

Related Manuals for DSC Power 832

Summary of Contents for DSC Power 832

  • Page 1 Installation Manual PC51O8L v1.O Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
  • Page 2 FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
  • Page 3 Introduction 1.1 Features The PC5108L serves three purposes: • To expand the PC5015 v2.2 alarm control panel’s zone capability by adding eight fully programmable zone inputs • To act as an interface between the DLM-4L v1.0L Video Transmission module and the PC5015 v2.2 alarm control panel •...

  • Page 4: Installation

    Installation 2.1 Unpacking the PC5108L The PC5108L product should include the following items: • one PC5108L module • five plastic stand-offs 2.2 Mounting the Unit The PC5108L should be located inside a compatible metal cabinet, mounted in a dry, secure location. Preferably, it should be placed close to the control panel and at a convenient distance from the connected devices.

  • Page 5: Applying Power

    Consult the following wiring diagram for further information: To DLM-4L To video input (TV/VCR) SYNC Input (for external dwell control) Normally Closed Tamper contact To DLM-4L: (If no contact used, To Keybus connect a wire from RED, BLK, TAMP to any COM YEL and GRN terminal.) on next module/...

  • Page 6: How To Program

    How to Program 3.1 Programming via Keypad The PC5108L can be programmed from a system keypad. To pro- gram the module, perform the following: 1. Enter [*][8] followed by your Installer’s Code. 2. Enter [806] to access PC5108L module programming. 3.
  • Page 7 Module Operation and Programming 4.1 Module Zone Group Assignment In order to use the zone expansion portion of the module, you must select which system zones the expander will occupy. Subsection [00] Module Zone Group Assignment will accept two digits. The first corresponds to zone terminals 1-4 on the module (Group A).
  • Page 8 M O D U L E O P E R A T I O N A N D P R O G R A M M I N G Since four images can be stored by the DLM-4L for each event, four timing and camera entries are required.
  • Page 9 M O D U L E O P E R A T I O N A N D P R O G R A M M I N G Pre-trigger The pre-trigger section can be programmed to allow Downlook to activate while the system is idle.

  • Page 10: Video Switching

    M O D U L E O P E R A T I O N A N D P R O G R A M M I N G 4.3 Video Switching The PC5108L can be used to connect each of the eight cameras one at a time to a monitor/video recorder.
  • Page 11 M O D U L E O P E R A T I O N A N D P R O G R A M M I N G Depending on the type of device connected, the SYNC input must be programmed for Normal or Inverted operation.

  • Page 12: Testing And Troubleshooting

    Testing and Troubleshooting 5.1 Camera Testing Cameras connected to the PC5108L can be tested on a regular basis. The DLM-4L must be connected in order to use the testing feature. Each camera must be enabled for testing. There is one Camera X Test Enable/Disable option for each camera.

  • Page 13: Programming Worksheets

    Programming Worksheets [806] PC5108L Module Programming [00] Module Zone Group Assignment Default = 00 l _ ____ l _ ____ l First digit = Zones on terminals Z1-Z4 (Group 1) Second digit = Zones on terminals Z5-Z8 (Group 2) 0 = Group Not Used 1 = Group Not Used 2 = Zones 9-12 3 = Zones 13-16...
  • Page 14 [27] Zone 27 l _ ____ l _ ____ l _ ____ l _ ____ l l _____ l _____ l _____ l _____ l l _ ____ l _ ____ l _ ____ l _ ____ l l _ ____ l _ ____ l _ ____ l _ ____ l [28] Zone 28 l _ ____ l _ ____ l _ ____ l _ ____ l l _____ l _____ l _____ l _____ l...
  • Page 15 Security Products © 1998 Digital Security Controls Ltd. 1645 Flint Road, Downsview, Ontario, Canada M3J 2J6 Tel. (416) 665-8460 • Fax (416) 665-7498 • Tech. Line 1-800-387-3630 • www.dscgrp.com Printed in Canada 29002769 R1...

  • Page 16: Limited Warranty

    LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd.

This manual is also suitable for:

Pc5108l

Table of Contents

Save PDF