Sealey STW292 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS
AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE
TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP
INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! DO NOT use the digital torque adaptor if

damaged or thought to be faulty.
DO NOT apply force to the digital torque adaptor when

the power is off. Always turn it on before using it,
otherwise it will be damaged.
DO NOT turn off the digital torque adaptor while torque

force is being applied to it.
DO NOT exceed the permitted maximum torque value.

To do so will cause it to break.
DO NOT subject the 3/4" connectors to any force other

than a rotational one.
Ensure that all components including all adaptors,

extensions, drivers and sockets are rated to match or
exceed the torque being applied.
Observe all equipment, system and manufacturer's

warnings, cautions and procedures when using this
digital torque adaptor.
Use the correct size socket for the fixing.

DO NOT use sockets that are worn or cracked.

Check that the digital torque adaptor capacity matches or

exceeds each application before proceeding.
Ensure all workshop safety rules, regulations, and

conditions are complied with when using this digital
torque adaptor.
Maintain correct balance and footing. Ensure the floor is

not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the

working area.
DO NOT press, pressure, or damage the LCD display.

DO NOT use near strong magnetic fields.

DO NOT subject to excessive force or shocks.

DO NOT drop or throw the digital torque adaptor.

DO NOT leave the digital torque adaptor in any place

exposed to excessive heat, humidity or direct sunlight.
DO NOT use organic solvents such as alcohol or

thinners for cleaning.
DO NOT submerge in water or any other liquid.

DO NOT disassemble the digital torque adaptor.

To ensure accurate measurement, periodic re-calibration

is necessary.
After use, clean with a soft dry cloth and store in a safe,

dry, childproof location away from any heat sources.
Avoid any dusty, damp or humid conditions.
2. INTRODUCTION
Designed for use with a standard ratchet or breaker bar. Ideal
for work around the engine bay and the tightening of wheel
nuts to factory specifications. Large LCD display with LED/
audible alarm indicating achieved and target torque levels.
Selectable readings in Nm, lb.ft or kg.m and accurate to ±2%
of stated capacity. Memory stores up to 50 readings and
features auto shut off after 80 seconds. Supplied with test
certificate and storage case.
© Jack Sealey Limited
INSTRUCTIONS FOR:
DIGITAL TORQUE ADAPTOR
3/4" Sq. Drive - 100 - 500Nm
MODEL No:
3.
MODEL:
Range:
Accuracy:
Resolution:
Drive:
Units:
Size (L x W):
Weight:
Operating Modes:
Memory Space:
Battery:
Battery Life:
Operating temp:
Storage temp:
Humidity:
fig.1
4.
NOTE: DO NOT press the Mem and Power buttons at the
4.1.
4.1.1. Unscrew the four cross-head screws holding the rear
NOTE: When battery power is low, a low battery icon will be
NOTE: DO NOT use the digital torque adaptor when the
Original Language Version
STW292
SPECIFICATION
STW292
100-500Nm/73.8-369lb.ft/10.19-50.98kg.m
±2%
0.1
3/4" Sq. Drive
Nm/lb.ft/kg.m
110mm x 56mm
570g
Trace & Peak
50
2 x AA Type
Up to 110 Hours
-10 ~ 60ºC/13.9 ~ 139.9ºF
-20 ~ 70ºC/-4 ~ 157.9ºF
15 ~ 90% Non-condensing
OPERATION
same time as this will enter calibration mode.
Preparation.
battery cover and remove the battery cover (fig.1).
Install two AA batteries, ensuring correct polarity. Refit
the battery cover and refit and tighten the four
cross-head screws.
displayed.
battery is in a low state of charge as this will affect the
torque adaptor's accuracy.
STW292 Issue No.1 26/07/12