Monacor security TVCCD-189HCOL Manual page 7

Order number 18.6050
Main menu line Submenu line
1. In the menu line DAY&NIGHT, select the setting COLOR to switch off the IR LEDs.
2. Cover the lens so that no light will fall on the CCD chip.
3. Press the control lever to call up the submenu.
START
DPC VIEW
DPC
(defective pixel correction) LS VALUE
DIFF.
AREA HS
AREA HE
AREA VS
AREA VE
RETURN
CAM TITLE
input of camera name
MOTION
settings for
motion detection
PRIVACY
masking of areas
SPECIAL
PARK. LINE
additional setting options
settings for parking lines
IMAGE ADJ.
settings for
image reproduction
COMM ADJ.
LANGUAGE
VERSION
RETURN
EXIT —
Selection / additional submenu Setting; function
To start the correction, press the control lever. On the monitor, COVER THE LENS THEN PRESS ENTER
— KEY will be displayed. Tilt the lever forward or backward to return to the submenu or press the lever once
again to start the correction.
OFF, ON The defective pixels will be shown after correction.
000 . . 016 . . 063 sensitivity for defective pixel correction
000 . . 010 . . 063 number of pixels used for comparison during defective pixel correction
001 . . 024 . . 255 definition of correction area: on the left
001 . . . . . . . 255 definition of correction area: on the right
001 . . . . . . . 255 definition of correction area: at the top
001 . . 127 . . 255 definition of correction area: at the bottom
RET ↵ , SAVE&END
RET = return to main menu, SAVE&END = save and exit menu
OFF, ON ↵
In the setting ON, a camera name to be inserted in the monitor image can be entered via a submenu.
0123456789ABCDEFGHIJ
Tilt the lever to select the desired character, press the lever to confirm and to go to the next character position.
... / = & : ~ , . ↵
▶
... VWXYZ
← →
go to previous position or next position
CLR delete name
POS define position of camera name
END return to the menu SPECIAL
In the setting ON, the symbol
OFF, ON ↵
(unless the menu is still displayed).
Four sensor areas can be defined via a submenu.
AREA SEL. 1 ... 4; selection of sensor area to be defined
AREA STATE ON = sensor area activated, OFF = sensor area deactivated
HEIGHT 000 . . 003 . . 015; height of sensor area
WIDTH 000 . . 003 . . 015; width of sensor area
LEFT / RIGHT 000 . . 002 . . 015; move sensor area to the left or to the right
TOP / BOTTOM 000 . . 002 . . 015; move sensor area up or down
DEGREE 000 . . 032 . . 255; response sensitivity
ON = The grid blocks where motion has been detected are also displayed.
VIEW
OFF = The grid blocks are not displayed (The settings ON and OFF apply to all sensor areas.)
RETURN RET = return to the menu SPECIAL, SAVE&END = save and exit menu
OFF, ON ↵
In the setting ON, 8 masks can be defined via a submenu.
AREA SEL. 1 ... 8; selection of the mask to be defined
AREA STATE ON = mask is visible, OFF = mask deactivated
HEIGHT 000 . . 032 . . 255; height of mask
WIDTH 000 . . 032 . . 255; width of mask
LEFT / RIGHT 000 . . 016 . . 255; move mask to the left or to the right
TOP / BOTTOM 000 . . 016 . . 255; move mask up or down
COLOR colour of mask (000 ... 015)
RETURN RET = return to the menu SPECIAL, SAVE&END = save and exit menu
OFF, ON ↵
In the setting ON, parking lines can be defined via a submenu.
LT 000 . . 107 . . 255; left line: move upper end point to the left or to the right
LB 000 . . 026 . . 255; left line: move lower end point to the left or to the right
RT 000 . . 177 . . 255; right line: move upper end point to the left or to the right
RB 000 . . 226 . . 255; right line: move lower end point to the left or to the right
F 000 . . 021 . . 255; move upper end points up or down
N 000 . . 063 . . 255; move lower end points up or down
T 001 . . 004 . . 015; setting of line thickness
V1 000 . . 035 . . 255; width of blue parking area
V2 000 . . 041 . . 255; width of green parking area
V3 000 . . 077 . . 255; width of yellow parking area
RETURN RET = return to the menu SPECIAL, SAVE&END = save and exit menu
OFF, ON; correction of lens shading at the edges of the image
LENS SHAD. In the setting ON, the correction level (LEVEL) can be changed and the centre of correction can be moved
horizontally (H-CENTER) and vertically (V-CENTER) via a submenu.
OFF, ON; in the setting ON, the digital noise suppression is activated
2DNR
The level of suppression can be defined in the menu line LEVEL of a submenu.
MIRROR OFF, ON = mirror inversion of the image
FONT COLOR The colour of the menu font and the colour of the camera name can be defined via a submenu.
CONTRAST 000 . . 143 . . 255; contrast setting
SHARPNESS 000 . . 016 . . 255; sharpness setting
CRT, LCD, USER; selection of the monitor type connected (CRT, LCD, other type) and setting of black level
DISPLAY (PED LEVEL), saturation (COLOR GAIN) and gamma correction (not available for CRT) via a corresponding
submenu
NEG. IMAGE OFF, ON = negative reproduction of the image
RETURN RET = return to the menu SPECIAL, SAVE&END = save and exit menu
↵
settings for remote control (not available for this camera)
... ENGLISH ... select one of 8 menu languages
— indication 00 00 00
RET ↵ , SAVE&END
RET = return to main menu, SAVE&END = save and exit menu
SAVE ↵
save and exit menu
exit menu without saving the settings
NOT SAVE ↵
However, the settings made will be preserved until the power supply has been switched off.
RESET ↵
reset to factory defaults (except LANGUAGE and CAM TITLE)
will keep flashing on the monitor for a few seconds after motion detection
Select menu item and
press lever.