1. Manuals
  2. Brands
  3. Huck Manuals
  4. Tools
  5. SFBTT15 BobTail
  6. Instruction manual

Huck SFBTT15 BobTail Instruction Manual

Hydraulic installation tool
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
BobTail® Hydraulic Installation Tool

Table Of Contents

2
3-4
6
6
7
8
9
10
11-14
September 21, 2020
HK1151

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SFBTT15 BobTail and is the answer not in the manual?

Questions and answers

Related Manuals for Huck SFBTT15 BobTail

Summary of Contents for Huck SFBTT15 BobTail

  • Page 1: Table Of Contents

    Instruction Manual BobTail® Hydraulic Installation Tool Table Of Contents Declaration of Conformity Safety Instructions Preparation for Use Pressure Settings Tool to Powerig® Set-up Operating Instructions Maintenance Disassembly & Assembly Preparation 10 Optional Equipment Components Drawings 11-14 September 21, 2020 HK1151...

  • Page 2: Declaration Of Conformity

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151)

  • Page 3: Safety Instructions

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Safety Instructions Bold, Italic type, and underline: WARNINGS: Must be understood to avoid severe personal injury. CAUTIONS: Show conditions that will damage II. PROJECTILE HAZARDS: equipment or structure. I. GENERAL SAFETY RULES: 1. A half hour long hands-on training session with III.
  • Page 4 SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Safety Instructions IV. REPETITIVE MOTION HAZARDS: VIII. VIBRATION HAZARDS: V. ACCESSORIES HAZARDS: VI. WORKPLACE HAZARDS: X. HYDRAULIC TOOL SAFETY INSTRUCTIONS: WARNINGS: Do not exceed maximum pull or return settings on tool. hose. Be sure all hose connections are tight. All tool hoses must be connected.
  • Page 5 SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) MAX OPERATING TEMP: 125° F (51.7° C MAX FLOW RATE: 7.57 l/m (9.5) (6.7) MAX INLET PULL PRESSURE: 6000 414 bar (1.2) (8.3) MAX INLET RETURN PRESSURE: 345 bar PULL CAPACITY: 62 kN (5.5)

  • Page 6: Preparation For Use

    (per recommended before using Huck equipment. manufacturer’s instructions) to prevent leaks and to ease When operating Huck equipment, always wear approved eye assembly. and hearing protection. Keep disconnected hoses, Be sure there is adequate clearance for the operator’s hands before proceeding.

  • Page 7: Tool To Powerig Setup

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Tool to Powerig Setup WARNINGS: To prevent tripping hazard, suspend tools and Only use compatible equipment with this tool. NOTE To decrease Relief Valve pressure, gradually turn the Relief Valve handle counterclockwise; turn clockwise to increase pressure.

  • Page 8: Operating Instructions

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Operating Instructions FOR SAFE OPERATION, THIS SECTION MUST BE READ AND UNDERSTOOD. Flange DOWN Do NOT pull a fastener Do NOT install a fastener without a CORRECT CORRECT with the collar upside workpiece (structure to be fastened), a pin, down.

  • Page 9: Maintenance

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Maintenance WARNINGS: CAUTIONS: Inspect your tool Replace all seals, wipers, and rings when tool is disassembled for any for damage and/or reason, and at regular intervals, depending on severity and duration of use. wear before every use.

  • Page 10: Disassembly & Assembly Preparation

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Disassembly and Assembly Preparation WARNING: Be sure to disconnect the tool’s electrical control CAUTION: ® trigger system from the Powerig Hydraulic Unit before tape on pipe threads. Tape can ® disconnecting the tool’s hydraulic hoses from it. If not disconnected in this order, severe personal injury could occur.

  • Page 11: Components Drawings

    SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Components Drawing - Head and Handle ORDER OF DISASSEMBLY: Figure 4 A & B C & D F & G contains End Cap and components 501145 contains Piston marked and components marked Apply Loctite 243, HUCK...
  • Page 12 SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Components Drawing - Tool Hoses and Cord Figure 5 Apply Loctite 242, HUCK p/n 505016, to these threaded joints per Apply Loctite 242, manufacturer’s HUCK p/n 505016, to instructions. these threaded joints per manufacturer’s instructions.
  • Page 13 SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Components Drawing IT - Head and Handle Figure 6 130198 130211 132056 132057 501149 Apply Loctite 243, HUCK p/n 508567 Apply Loctite 243, to threads per HUCK p/n 508567 manufacturers to threads per instructions.
  • Page 14 SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Components Drawing IT - Tool Hoses and Switch Assy. Figure 7 Apply Threadmate, Apply Threadmate, HUCK p/n 508517 to HUCK p/n 508517 to these threaded joints these threaded joints per manufacturers per manufacturers instructions...
  • Page 15 SFBTT15 BobTail® Hydraulic Installation Tool (HK1151) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: Tooling, Part(s) and Other Items not manufactured by Huck: useful lifetime Two Year Limited Warranty on Installation Tools: ® Huck Installation Equipment: literature. 90 Day Limited Warranty on Nose Assemblies and Accessories: literature.

Table of Contents