Page 1
SERVICE MANUAL US Model Canadian Model Ver. 1.0 2011.12 AEP Model UK Model E Model Australian Model • HBD-TZ140 is DVD receiver in DAV-TZ140. Model Name Using Similar Mechanism Mechanism Type F-8829F1 Optical Pick-up Block Name CMS-S76RFS3G SPECIFICATIONS AUDIO POWER SPECIFICATIONS...
Page 2
THESE COMPONENTS WITH SONY PARTS PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. PUBLIÉS PAR SONY.
Page 3
HBD-TZ140 TABLE OF CONTENTS SERVICING NOTES ..........DISASSEMBLY 2-1. Disassembly Flow ............2-2. SS Top Cover ..............2-3. Door ................2-4. POWER Board ..............2-5. Front Cabinet Block ............10 2-6. STANDBY Board, CONTROL Board ......11 2-7. DVD Mechanism Deck (F-8829F1) ....... 12 2-8.
Page 4
HBD-TZ140 SECTION 1 SERVICING NOTES VERSION DISPLAY NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT Confi rmation procedure of version only: 1. Connect this unit with TV monitor. The laser diode in the optical pick-up block may suffer electro- 2.
Page 5
HBD-TZ140 MODEL IDENTIFICATION NOTE OF REPLACING THE IC101, IC102 AND IC103 ON THE MAIN BOARD AND THE COMPLETE MAIN BOARD – Back cabinet – When IC101, IC102 and IC103 on the MAIN board and the Part No. complete MAIN board are replaced, it is necessary to spread the compound (THERMAL COMPOUND (G747)) (Part No.
Page 6
HBD-TZ140 HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF 2 Insert the tweezers etc. in the hole of the chassis, and push the lever in the direction 1 Remove the sheet. 4 Paste the sheet again. of the arrow.
Page 7
HBD-TZ140 POWER BOARD SERVICE POSITION • Connect the MAIN board (CN500) and the POWER board (CN901) with the jig cable. Jig cable: Part No. Description A-1866-921-A TZ140/145 SERVICE JIG ASSY MAIN board MAIN board (CN500) POWER board POWER board (CN901)
Page 8
HBD-TZ140 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. SS TOP COVER (Page 8) 2-3. DOOR 2-4. POWER BOARD (Page 9) (Page 9) 2-5. FRONT CABINET BLOCK 2-7. DVD MECHANISM DECK BLOCK...
Page 9
HBD-TZ140 2-3. DOOR 6 door 5 five claws 2 Insert the tweezers etc. in the hole of the chassis, and push the lever in the direction 1 Remove the sheet. 4 Paste the sheet again. of the arrow. – Bottom view –...
Page 10
HBD-TZ140 2-5. FRONT CABINET BLOCK Wire e i Bring the slack part to the front side. CONTROL board DVD mechanism deck POWER board (CMS-S76RFS3G) wire tie 1 Cut two wire ties. Note: In reassembling, use new wire tie to fasten the clamp same as before.
Page 11
HBD-TZ140 2-6. STANDBY BOARD, CONTROL BOARD • Front cabinet inner view Wire e i CONTROL board STANDBY board claw claw 1 two claws 8 two claws 3 two claws 2 screw (BVTP2.6) 4 STANDBY board 6 grounding spring sheet 5 screw (BVTP2.6)
Page 12
HBD-TZ140 2-7. DVD MECHANISM DECK (F-8829F1) Note 1: When disconnecting the fl exible cable of optical pick-up block, solder the short-land. 1 Cut two wire ties. <Fig. A> Note 2: In reassembling, use new wire tie to fasten the clamp same as before.
Page 13
HBD-TZ140 2-8. FFC HOLDER 4 FFC holder block 7 FFC holder 2 Remove the FFC holder 5 two claws block in the direction of the arrow. 3 flexible cable 1 claw 6 flexible cable 1 claw – DVD mechanism deck bottom view –...
Page 14
HBD-TZ140 2-9. OPTICAL PICK-UP (CMS-S76RFS3G) 1 insulator screw 5 optical pick-up (CMS-S76RFS3G) 3 connector 4 insulator 1 insulator screw 1 insulator screw 4 insulator 4 insulator 1 insulator screw 2 Remove the optical pick-up 4 insulator (CMS-S76RFS3G) in the direction of the arrow.
Page 16
HBD-TZ140 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. – POWER Board – IC900 SSC620SA (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. +7.6 V Note: Note: •...
Page 17
HBD-TZ140 IC101 – 103 STA518 IC205 TP2041BDBV GND-SUB 1 CURRENT OUT 1 VccSign OUT2B 2 SENSE GND 2 VccSign OUT2B 3 CHARGE Vcc2B 4 PUMP IN2B CURRENT DRIVER IN2A LIMIT GND2B 5 IN1B UNDER GND2A 6 IN1A VOLTAGE OC 3...
Page 28
HBD-TZ140 3-12. SCHEMATIC DIAGRAM - MAIN Board (5/5) - • See page 16 for IC Block Diagrams. MAIN BOARD (5/5) IC200D VCC33_RF FB500 100 L500 10uH VCC33 AVDD3 DACVDDA VCC33 L501 10uH VCC1V8 SVDD3 DACVDDB VCC33 FB501 PLLVDD3 VCC33 L502...
Page 29
HBD-TZ140 SECTION 4 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Abbreviation The components identifi ed by mark 0 they may have some difference from the : Australian and New Zealand or dotted line with mark 0 are critical for original one.
Page 30
HBD-TZ140 4-2. CHASSIS SECTION not supplied MAIN board not supplied not supplied not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-2583-544-1 FRONT CABINET ASSY BLK (U) (US) 9 59...
Page 31
HBD-TZ140 4-3. DVD MECHANISM DECK SECTION (F-8829F1) not supplied not supplied not supplied not supplied supplied not supplied not supplied not supplied not supplied FFC1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FFC1 9-885-166-72 FLEXIBLE CABLE (24P) (US)
Page 32
HBD-TZ140 SECTION 5 CONTROL MAIN POWER ELECTRICAL PARTS LIST STANDBY Note: • Due to standardization, replacements in • SEMICONDUCTORS When indicating parts by reference num- the parts list may be different from the In each case, u: μ, for example: ber, please include the board name.
Page 34
HBD-TZ140 REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2011.12...
Need help?
Do you have a question about the HBD-TZ140 and is the answer not in the manual?
Questions and answers