Table of Contents
Advertisement
Programming Software Installing and Starting (in windows XP system)
Double click "TYT TH-9000D", then follow the
installing instruction.
Install USB Cable Driver Programme
1. Click start menu in computer, under "ALL
PROGRAMS" menu, choose and click "USB
To Com port" in TH-9000D program, install
"USB To Com port" driver by indication.
2. Connect the optional USB Programming
cable to USB port in PC with transceiver.
(As pic 1)
3. Double click TH-9000D shortcut or click
TH-9000D in procedure index of start menu,
choose serial com port as indicated then click
OK to start programming software. (As pic 2)
4. According to instruction,select correct"COM
Port"(As pic 3),then click "OK" to start
programming software.
56
NOTE: Even in same computer,the selective COM Port is different when USB cable
connects with different USB port.
You shall install software before connecting the USB cable line. Switch on transceiver
before writing frequency.You had better not switch on or off the power supply of transceiver
when it is connected with computer, otherwise, it will make transceiver unable to read or
write frequency. In this case, you have to turn off programming software, pull out USB cable.
(As pic 1)
then reinsert USB cable and open software, then rechoose COM Port, it will turn into normal
operation. Therefore, please connect transceiver with computer after switching on the
transceiver. Don't restart transceiver power when it is connected with computer.
NOTE: This software has productidentify system, so when firstly installing the software,
you have to connect the products, otherwise you can not start the software.
(As pic 2)
(As pic 3)
57
Advertisement
Table of Contents
Need help?
Do you have a question about the TH-9000D and is the answer not in the manual?
Questions and answers
как переклучить диапазон
To switch the band on the TYT TH-9000D:
1. Press and hold the key for over 2 seconds to enter the general setting menu.
2. Press the P1 or P2 key to choose menu No.08, which displays "BAND--25".
3. Turn the selector knob to select the desired bandwidth setting:
- 25: Wide band (25 kHz)
- 12: Narrow band (12.5 kHz)
This answer is automatically generated
VHF136-174 и 220-260 MHz. не найду где переключить?
VHF136-174 как перейти на диапазон 220-260 МГц
The TYT TH-9000D operates in the 220–260 MHz range by default, with 220–225 MHz being the ham radio portion in the U.S. No manual switching is required to access this range; the radio is designed to cover it.
This answer is automatically generated
как мне настроить на частоте.1455000 приём передачу?
To set up the TYT TH-9000D for transmitting and receiving on 145.5000 MHz, follow these steps:
1. Turn on the radio.
2. Switch to VFO mode by pressing the P3 button until the frequency is displayed (not channel number).
3. Enter the frequency:
- Pick up the microphone.
- Use the keypad to enter 145.5000.
4. Set the tone or offset if needed:
- If no tone or offset is required, skip this step.
- If a CTCSS tone or offset is needed, set it accordingly using the function menu.
5. Save the frequency to a channel (optional):
- Hold the Function key until the channel number blinks.
- Use the microphone to select a channel number.
- Press P3 to save.
The radio is now set to transmit and receive on 145.5000 MHz.
This answer is automatically generated
как настроить репетитор радиостанция
как настроить радиостанцию на репитер
ТОН 1750 ГЦ ДЛЯ ДОСТУПА К РЕПИТЕРАМ как настроить
как включить репитер
где кнопка включения репитера?