Sealey BG1010 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer instruction Wear eye
manual protection
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Inspect power supply cables and plugs regularly for wear or damage and check all connections to
ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. have any faulty item repaired or
replaced immediately by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that
the restraint is tight.
Double insulated products, which are always marked with this symbol
To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable. If an extension reel is to be used outdoors, ensure it is marked for outdoor use.
1.2 GENERAL SAFETY
Disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.

Replace damaged parts. Use genuine parts only. Unapproved parts may be dangerous and will invalidate the warranty.

Wear approved safety goggles, safety gloves,appropriate dust mask if grinder generates dust.

Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.

Use the grinder in a suitable work area, keep area clean, tidy and free from unrelated materials, and ensure adequate lighting.

Maintain correct balance and footing. DO NOT over-reach and ensure the floor is not slippery. Wear non slip shoes.

Do not allow children to play with this machine: keep it out of their reach.

DO NOT operate the grinder if any parts are missing or if the grinder is damaged.

DO NOT use the grinder for a task it was not designed to perform.

DO NOT get the grinder wet or use in damp or wet locations.

DO NOT switch the grinder on whilst the wheel is in contact with the workpiece.

DO NOT touch the workpiece immediately after grinding or polishing as it may be very hot.

DO NOT touch the wheel whilst operating, or whilst plugged into the mains power.

DO NOT leave the grinder running unattended.

DO NOT operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.

When not in use, switch the grinder off and remove the plug from the power supply.

© Jack Sealey Limited
INSTRUCTIONS FOR:
MINI BENCH GRINDER Ø50MM -
FLEXIBLE DRIVE SHAFT
MODEL NO:
Indoor Use
Only
Original Language Version
BG1010
, are fitted with live (brown) and neutral (blue) wires only.
RECOMMENDED FUSE
RATING: 3A
BG1010 Issue: 1 - 18/06/15