Table of Contents
Advertisement
Quick Links
Features:
Supplied ready to operate
•
Replaces "Switched Live Cables"
•
Quick and Simple to Install
•
Up to 5Km range line of sight.
•
Up to 1Km range in buildings
•
Simple Screw Terminal Connec-
•
tions
Operates from 110Vac or 230Vac
•
Spread Spectrum RF Modulation
•
Weatherproof IP68 Enclosures
•
RED Compliant and FCC Certified
•
High Quality UK manufacture
•
Description
MAINSLINK-PRO removes the need to lay all "Switched Live Cables" between the Boil-
er and the wiring Centre. It provides a bi-directional two way 230Va switching RF link.
MAINSLINK-PRO consists of two identical units. One unit is installed by the boiler and
the other within the wiring Centre.
Each unit has a 'Live In', and a 'Live Out' screw terminal . When the 'Live in' is 'LIVE'
at one unit it sends an RF signal to the other unit which switches its 'Live out' 'LIVE' ,
and vice versa,
MAINSLINK-PRO utilises the RF Solutions state of the art RF-LoRa Spread Spectrum
Frequency Modulation transceiver design to achieve a the highest performance / Range
available from any Radio System.
Ordering Information
Part Number
MAINSLINK-PRO
PATENT No 2564512
2 Way Boiler & Pump Control
System consisting Pair of Transceiver units
DS-MAINSLINKPRO-3
MAINSLINK–PRO
Description
Advertisement
Table of Contents
Related Manuals for RF SOLUTIONS MAINSLINK–PRO
Summary of Contents for RF SOLUTIONS MAINSLINK–PRO
- Page 1 RF signal to the other unit which switches its ‘Live out’ ‘LIVE’ , and vice versa, MAINSLINK-PRO utilises the RF Solutions state of the art RF-LoRa Spread Spectrum Frequency Modulation transceiver design to achieve a the highest performance / Range available from any Radio System.
- Page 2 MAINSLINK-PRO Application example: WORCESTER-BOSCH Boiler Installation CH ON This system provides two functions, Switching of the Pump from the boiler and Switching of the Boiler from the wiring Centre. Connections at the Boiler The boiler output to the Pump is connected to the MAINSLINK-PRO A, (Lin) The boiler switching input is connected to the MAINSLINK-PRO A (Lout) It is recommended to use a single switch fuse spur to supply the Boiler and Mainslink together.
- Page 3 MAINSLINK-PRO Installation Connect the Supply to both units Connect the permanent LIVE Feed and NEUTRAL supply. Permanent Connect the Switched Input Lin LIVE FEED Connect the Switching Live input to Lin When the Switched Live input (LIN) is ’LIVE’ the Lin will illuminate, and the Lout at the other unit will then switch Live WDOG...
- Page 4 MAINSLINK-PRO Dimensions and Wall mounting information: MAINSLINK-PRO is a professional use product and should only be installed by a competent person. The product must be FIXED to the wall (EN60950 4.1) Holes 70 30.00 Dims in mm PATENT No 2564512 DS-MAINSLINKPRO-3...
- Page 5 RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how t o deploy or use R F Solu- tions Ltd’s products.
- Page 6 MAINSLINK-PRO Advanced Operation—Pairing together two MAINSLINK-PROs NOTE: This system does not require pairing, they are supplied ready to operate! This process is described for advanced use only. 1. Apply a 230Vac supply to the first MAISNLINK-PRO 2. Briefly place a magnet across enclosure (Right side as shown) to activate the internal reed switch.
- Page 7 MAINSLINK-PRO Jumper Link Setting There are three Jumper Links which may be used to configure the following Permanent Link Open Fitted LIVE FEED WDOG Watchdog OFF Watchdog Active WDOG MODE MODE LORA Mode 3 LORA Mode 7 MOM/LAT MOM/LAT Momentary Latching WDOG - WATCHDOG This provides improved reliability and security useful in with electrically noisy Loads.
- Page 8 MAINSLINK-PRO Product Revision History The below shows the product Development / Improvements that have been made to the product through the product Lifecycle EZTEXT REVISION CHANGE HISTORY Date Product Change / Improvement Change Revision Update to firmware to prevent lockup when pairing in Mode7. Using Mode 7 only the length of RF packet is >2secs, if, when in LEARN mode both MAINSLINK-PRO transmit at the same time then they can both be in the 18/10/18...
Need help?
Do you have a question about the MAINSLINK–PRO and is the answer not in the manual?
Questions and answers