ELUSIVE WILDLIFE The Kill Light Sportsman Manual

The Sportsman™ Solar Powered Motion Activated Light
Thank you for purchasing the Kill Light
Motion Activated Light from Elusive Wildlife Technologies, LP. If you have
not already done so, please check your local game laws to ensure it is
legal to use an artificial light source while hunting or observing animals at
night. Elusive Wildlife Technologies, LP and its affiliates do not condone or
promote the use of any of our products as a means to illegally harvest any
animal. Please take a moment to read these instructions thoroughly before
initial use.
TOP
Bottom
Warranty
Elusive Wildlife Technologies, LP warranties this product for a period of 1
year from original date of purchase. This warranty covers manufacturer
defects as well as malfunction during normal operation. Please complete
the warranty registration and mail in along with proof of purchase to
register your light. You may also e-mail your registration and proof of
purchase to info@elusivewildlife.com.
Your Kill Light® Sportsman™ Motion Activated Light is water resistant
when installed with the solar panel facing up. Do not submerse your
light, this will void your warranty. Take care to insure the light is mounted
properly and securely.
Elusive Wildlife Technologies, LP will not warranty any light damaged by
user neglect or failure to adhere to these instructions and guidelines. No
lights will be warrantied due to animal damage, or theft.
Sportsman™ Solar Powered
®
Durable Metal Housing
Solar Charger
Internal Battery for
All Night Run Time
Dusk-To-Dawn Sensor
Charging Indicator
On/Off
Mode Selector Button
Mounting Bracket Slot
Motion Sensor
High Output LED Panel
Quick Start Guide
To activate the light or change modes, insert the included Key Pin into the
small hole labeled ON/OFF to press the button. Wait for the light to stop
flashing before pressing the button again to move to a different mode.
IMPORTANT:
Choose a location that receives full sun and is oriented south.
Mode 1 Power Saver Mode. The light will flash one time. Turns on 50%
power when motion is detected. (Recommended Mode For
Longest Battery Life).
Mode 2 All Night Power Saver Mode. The light will flash two times.
Stays on 10% power all night. Increases to 50% power when
motion is detected.
Mode 3 Extreme Bright Mode. The light will flash three times.
Gradually increases to 100% power when motion is detected.
Mode 4 All Night Extreme Bright Mode. The light will flash four times.
Stays on 10% power all night. Gradually increases to 100%
power when motion is detected.
Mode 5 All Night Acclimation Mode. The light will flash five times.
Stays on all night at 25% power, every night, to acclimate the
animals to the light.
OFF
The light will flash six times and turn off.
Mounting
1
2
3
4
Remove The Kill Light® Sportsman Motion Activated
Light from the package and place in direct sunlight
for a full day or install early in the morning to ensure
the light is fully charged before installation. Leave
the protective film on the solar panel until after
installation to prevent scratching during mounting.
The charge indicator light will illuminate red when
the solar charger is receiving sunlight.
Select a location that will receive full sunlight all
day. It is important that the light face the South so
that it receives the most sunlight. If the light is not
facing South, or if the light receives partial sunlight
it may not receive a full charge. If the light does not
receive a full charge it may not work properly and/or
ruin the battery.
If mounting to a feeder, align the mounting bracket
to the very bottom of the feeder, and mark the
screw holes. Use the included self drilling/tapping
screws to attach the bracket to the feeder. NOTE:
Apply some silicone to the mounting screw holes
or across the top of the mounting bracket to avoid
water seepage into the feeder.
Then slide the light onto the mounting bracket
and tighten the locking screws on the back of the
mounting bracket.
If mounting to a tree or post, slide the light onto the
mounting bracket, and tighten the locking screws
on the back of the bracket.
Then use the included screws to attach to the post or
tree. NOTE: Angle the mounting screws downward
to avoid damaging the solar panel with the screw
driver.
Remove the protective film from the solar panel.