Catalog Instruction Notice Charging Instruction Drone Specification Transmitter Transmitter Installation Frequency Pairing Checklist before Flight Calibration Instruction Flying Control Functions Introduction Altitude Hold Mode High / Medium / Low Speed Mode Flip Mode Heading Hold Mode Low Battery Alarm Out of Range Alarm Propellers Stuck Protection Propeller Installation Diagram Download and Install the APP: Flyingsee...
Instruction Thank you for buying UDIRC's product. This remote control model is designed for easy operation but with great functions such as altitude hold and 3D stunt. Please read the user manual carefully and following all instruction. Keep this user manual for further reference about daily maintained.
Page 4
(3) Keep away from humid environment The drone inside is consisted of precise electronic components. Humidity or water vapor may damage electronic components and cause accident. (4) Safe operation Please operate the RC drone in accordance with your physical status and flying skill.
Charging Instruction 1. Connect the drone battery with USB plug first and then choose one of the method as below picture shown to connect with USB plug. (prior to choose 2A, 5V charger) 2. The red USB indicator light keeps bright when charging. The light turns green when fully charged.
Name Name A Propeller (Clockwise) Drone Battery Clockwise Motor (Red and Blue Wire) Camera Board Tail Light (Red) Camera Cover B Propeller (Counterclockwise) Right Landing Gear Counterclockwise Motor (Black and White Wire) Camera Antenna Front Light (Green) Left Propeller Guard Right Propeller Guard Battery Cover Upper Cover...
Page 8
Mobile Phone Holder Take Off / Landing / Heading Hold Mode Emergency Stop Button Picture 4 Strong/Weak Emission Transmitter Battery Signal Indication Forward / Backward Low /Medium / Trimming Indication High Speed Left / Right Flying Left / Right Rudder Trimming Indication Trimming Indication Throttle Digital Display...
Transmitter Installation: Battery installation: open the battery cover on the back side of the transmitter and put 4 alkaline batteries (AAA, not included) into the box in accordance with electrode instructions, as Picture 6 and Picture 7 shown. 4*1.5V Alkaline Batteries Picture 6 Battery Cover Picture 7...
3. Put the drone on the flat surface, the drone body lights turn from flashing to solid bright, which indicates successful frequency pairing. Important Notice: Please make sure the drone is placed on the horizontal position after powering on the drone, so that the drone can work well. Picture 11 Picture 12 Picture 13...
3. Power on the drone and put it on a flat surface in a horizontal position. The drone body lights change from flashing to solid bright, which indicates successful frequency pairing. 4. Do not move the Left Stick before successful calibration.
7. If the drone tilts to the left or right Press the Right Trimmer till balance if the drone drifts to the left, and press the Left Trimmer till balance if the drone drifts to the right. Drift left Drift right Functions Introduction Picture 20 Two Take Off Methods...
High / Medium / Low Speed Mode 1. Low Speed Mode is suitable for beginner. 2. Medium Speed Mode is suitable for user to fly the drone in breeze. 3. High Speed Mode is suitable for expert to High / Medium / Low Speed Mode (Press Down) experience aerial stunt in outdoor.
Prerequisite: Position the drone in such a way that its front is your front (see Picture 1). Tip: Do not change the orientation of the transmitter (see Picture 2) after entering heading hold mode. Front Front (Green Light) (Green Light) Left Right Left...
1. Install the battery to the mounted box and power on the drone. Put the drone on the flat surface in horizontal position. 2. Enter “set up” of the mobile phone, turn on WiFi (WLAN) and choose udirc-***, return to desktop after successful connection.
Or it may be fail to be controlled. 3 . Introduction for APP Icons 3.1 Home Page Icons Help Explore UDIRC Drone Learn the operation of Drone Media Remote control interface 3.2 Remote Control Interface Home Page Icon Click on the icon and back to home page.
Page 17
Remote Control Signal To show the drone’s WiFi signal strength. Setting Click on this icon to set some parameters, and click again to exit. SETING Click on “Save” to save trimming setting. Trimming Save Reset Choose “Reset” for factory reset. Transmission quality 720P 480P...
Photo Click on this icon to take photo. Heading Hold Mode Click on this icon and it turns red, which indicates that the drone enter Heading Hold Mode. Click again to exit from Heading Hold Mode. The icon turns white. Media Click on this icon to view or delete the aerial video and photo.
Page 19
To fly up or down Move the Left Ball up to fly the drone up and move the Left Ball down to fly the drone back down. The drone will stay flying at appointed altitude. To rotate left or right: Move the Left Ball to the left to rotate the drone to the left.
Page 20
5.1 Trimming Adjustment If the drone tilts forward or backward Click the “-” of the Forward / Backward Trimmer to adjust the drone till balance if the drone tilts forward. Click the “+” to adjust the drone till balance if the drone tilts backward. If the drone rotates to left or right Click the “+”...
6. Media To view the photos and videos. FLYINGSEE 1.0 Home To view the aerial photography dates saved Explore UDIRC Drone in the TF card. Learning Drone Remote control interface My Gallery Internal Memory Help 本地图库 外存储器 News Notice Main Menu...
Spare Parts For convenience, the spare parts are listed for you to choose, which can be purchased from the local seller. (Please refer to the exploded view in P6 - P7 to check the circled icon) U28W-01 U28W-02 U28W-03 U28W-04 Upper Cover Lower Cover Propeller...
Troubleshooting Guide Problem Problem Cause Solution 1. Low battery. 1. Replace the transmitter battery. 2. The battery positive pole and negative 2. Install the battery in accordance with the transmitter pole are in reverse order. user manual. indicator light is off 3.
FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rul es.These limits are designed to provide residential protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the PEREGRINE and is the answer not in the manual?
Questions and answers