Related Manuals for Fimap Genie B
Summary of Contents for Fimap Genie B
- Page 1 USE AND MAINTENANCE MANUAL GENIE B ED. 02-2015 Original instructions Doc. 10005707 Ver.
- Page 2 The descriptions contained in this document are not binding. The company therefore reserves the right to make any modifications at any time to elements, details, or accessory supply, as considered necessary for reasons of improvement or manufacturing/commercial requirements. The reproduction, even partial, of the text and drawings contained in this document is prohibited by law.
-
Page 3: Table Of Contents
CONTENTS ON CONSIGNMENT OF THE MACHINE ............................4 SERIAL NUMBER PLATE ................................4 INTRODUCTORY COMMENT ............................... 4 INTENDED USE ..................................... 4 TECHNICAL DESCRIPTION ................................5 SYMBOLS USED ON THE MACHINE ............................6 GENERAL SAFETY REGULATIONS ............................7 MACHINE PREPARATION ................................8 HANDLING THE PACKED MACHINE .......................... -
Page 4: On Consignment Of The Machine
Introductory comment GENIE B is a floor scrubbing machine which, via the mechanical action of the rotating brush and the chemical action of a water/detergent solution, can clean any type of flooring. -
Page 5: Technical Description
TECHNICAL DESCRIPTION Genie B Rated power Working width Width of rear squeegee Work capacity 1050 Water consumption mm Brushes (diameter or length) Brush rotations Pressure on the brushes Brush motor V / W 12 / 250 Type of advance Semi-aut. -
Page 6: Symbols Used On The Machine
SYMBOLS USED ON THE MACHINE Tap symbol Used to indicate the solenoid valve switch Brush symbol Used to indicate the brush motor switch Symbol denoting suction motor Used to indicate the suction motor switch Battery symbol Battery charge level indicator Indicates the maximum temperature of the detergent solution Located near the solution tank inlet Indicates the maximum gradient... -
Page 7: General Safety Regulations
Otherwise, request the intervention of the FIMAP technical assistance centre. If you need to replace any components, request the ORIGINAL spare parts from a FIMAP dealer and/or Authorised Retailer. Before carrying out any maintenance work, switch off the machine and disconnect the battery connector. -
Page 8: Machine Preparation
MACHINE PREPARATION 1. HANDLING THE PACKED MACHINE The machine is contained in specific packaging. Every pallet consists of four machines arranged on two levels. It is not possible to place more than two packages on top of each other. The total weight is 70kg The overall dimensions of the package are: 500mm 500mm... -
Page 9: Inserting/Connecting The Batteries
MACHINE PREPARATION 4. INSERTING/CONNECTING THE BATTERIES The machine is supplied with a built-in battery charger and an airtight gel battery. If you use batteries other than those supplied with the machine, use only 12V AGM or Gel batteries and proceed as follows. The batteries must be housed in the special compartment beneath the solution tank. -
Page 10: Connecting The Connector
MACHINE PREPARATION 5. CONNECTING THE CONNECTOR 1. Connect the battery connector to the machine connector. 2. reassemble all the elements WARNING: this process must be carried out by qualified personnel. The incorrect or imperfect connection of the cables to the connector can seriously harm people and damage objects. 6. -
Page 11: Charging The Battery (With Built-In Battery Charger)
MACHINE PREPARATION 8. CHARGING THE BATTERY (WITH BUILT-IN BATTERY CHARGER) Perform a battery charging cycle before using the machine. When replacing the battery, be sure to use batteries that are suitable for the battery charger installed (use only 12V AGM or Gel batteries). In order to recharge the battery: 1. -
Page 12: Battery Indicator
MACHINE PREPARATION 9. BATTERY INDICATOR The battery indicator is digital, with 4 fixed positions and a flashing one. The numbers which appear on the display show the approximate charge level. 4 = maximum charge 3 = ¾ charge 2 = 2/4 charge 1 = 1/4 charge 0 = discharged batteries (flashing) WARNING: a few seconds after the appearance of the flashing... -
Page 13: Machine Preparation
MACHINE PREPARATION 11. FIXING THE HANDLEBARS For packaging purposes the handlebars are supplied folded; they must now be put in the working position. Proceed as follows: 1. raise the handlebars by pulling upwards the lever indicated by the arrow 2. put the machine in the working position 3. -
Page 14: Recovery Tank
MACHINE PREPARATION ATTENTION: always use detergents whose manufacturer's label indicates their suitability for scrubbing machines. Do not use acid or alkaline products or solvents without this indication. always use low foam detergent. To avoid the production of foam, before starting to clean, put a minimum quantity of antifoam liquid into the recovery tank. -
Page 15: Work
WORK 1. PREPARING TO WORK Before fitting the tanks, it is necessary to carry out certain operations: 1. Open the two rear hinges of the battery compartment 2. Connect the connector to the batteries 3. Close the battery compartment 4. Make sure that the recovery tank is empty 5. -
Page 16: At The End Of The Work
AT THE END OF THE WORK At the end of the work, and before carrying out any type of maintenance, perform the following operations: 1. Turn off the solenoid valve switch (3) 2. Turn off the suction switch (2) 3. Turn off the brush / main switch (1) 4. -
Page 17: Daily Maintenance
DAILY MAINTENANCE PERFORM ALL MAINTENANCE OPERATIONS IN SEQUENCE 1. CLEANING THE RECOVERY TANK 1. Remove the tubes attached to the connectors of the recovery tank cap 2. Disconnect the recovery tank from the handlebars 3. Remove the cap and empty the tank 4. -
Page 18: Replacing The Squeegee Rubbers
DAILY MAINTENANCE 3. REPLACING THE SQUEEGEE RUBBERS Check the state of wear and tear of the squeegee rubbers and, if necessary, replace them. To replace them you must: 1. Raise the squeegee 2. Remove the two knobs 3. disassemble the squeegee from its support 4. -
Page 19: Periodic Maintenance
PERIODIC MAINTENANCE 1. CLEANING THE SQUEEGEE TUBE Periodically, or whenever suction seems to be unsatisfactory, check the squeegee tube is not obstructed. To clean it, proceed as follows: 1. remove the tube from the sleeve on the squeegee 2. remove the other end from the recovery tank 3. -
Page 20: Troubleshooting
To restore the power supply to the motor, switch off the machine and wait for the fuses to cool down (about 40 seconds). If the switch disconnects the current again, contact the FIMAP technical assistance centre. -
Page 21: Choosing And Using The Brushes
TABLE FOR CHOOSING THE BRUSHES Bristles Brush Machine Code Type of bristles Notes No. of brushes 421701 GENIE B 422213 Pad holder – anchor 422001 Pad holder – bristles... -
Page 22: Machine Disposal
MACHINE DISPOSAL To dispose of the machine, take it to a demolition centre or an authorised collection centre. Before scrapping the machine it is necessary to remove and separate the following materials and send them to the appropriate collection centres in accordance with the environmental hygiene regulations currently in force: ... -
Page 23: Ec Declaration Of Conformity
The technical documentation is kept by Mr. Giancarlo Ruffo, via Cà Nova Zampieri, n.5 – 37057 San Giovanni Lupatoto (VR) - Italy Santa Maria di Zevio, 01/10/2010 FIMAP S.p.A. Legal representative Giancarlo Ruffo FIMAP spa Via Invalidi del Lavoro, 1 - 37050 S.Maria di Zevio (Verona) Italy Tel. +39 045 6060411 r.a. - Fax +39 045 6060417 - E-mail:fimap@fimap.com - www.fimap.com...
Need help?
Do you have a question about the Genie B and is the answer not in the manual?
Questions and answers