Omron H3CR-F Series Instruction Manual

H3CR-F
C
J
INSTRUCTION MANUAL
UK/USA
Thank you for purchasing this OMRON product. This manual
primarily describes precautions required in installing and
wiring the timer. Before operating the product ,read this
manual thoroughly to acquire sufficient knowledge of the
product. Keep this manual for future reference.
© All Rights Reserved
www.fa.omron.co.jp
2256877-3B
1 OFF ON OFF ON
*
H3CR-F8(-F )
t 1 t 2 t 1 t 2
1
*
* 1
* 1
OFF * 2
ON * 3
1
*
H3CR-F8N(-FN )
ON OFF ON OFF ON OFF ON
t t t t
2 1 2 1
* 1
* 1
1
*
* 2
OFF
* 3
ON
H3CR-F8, -F8N H3CR-F, -FN
C
・ AC100 240V 50/60Hz/DC100 125V
・ AC24 48V 50/60Hz/DC12 48V
85 110 DC12V 90 110
0.1s
・ AC100 240V/DC100 125V AC240V 60Hz
ON 2VA 1.6W
OFF 1.3VA 1.1W
・ AC24 48V/DC12 48V DC24V
ON 0.8W
OFF 0.2W
10
（
AC250V/DC30V 5A
DC125V 0.15A
cosφ 1
DC5V 10mA P
10 55
25 65
35 85
C
(1)
(2)
(3) 10
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11) OFF
(12) ・
(13) / LED LED/
(14)
(15)
(16)
(17)
(18)
(19)
(20) EN/IEC
EMC
class A
IEC60664
C
*
(sec,10s,min,10min,hrs,10h)
OFF
sec
ON
6
OFF
4 8
2 10
0 12
OFF
0 min
ON
ON
H3CR
*
(sec,10s,min,10min,hrs,10h)
(1.2, 3, 12, 30)
sec
min
OFF ON OFF C
t 1 t 2 t 1
● OFF
*1 -F
*2 OFF
*3 ON
● ON
t t t
2 1 2
*1 -FN
*2 OFF
*3 ON
C
AC100 240V 50/60Hz/DC100 125V
AC24 48V 50/60Hz/DC12 48V
85 110
AC100 240V/DC100 125V AC240V 60Hz
ON
OFF
AC24 48V/DC12 48V DC24V
ON
OFF
10
AC250V/DC30V 5A
DC125V 0.15A
DC5V 10mA P
10 55
25 65
35 85
(1)
(2)
3
(3)
3
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11) OFF
(12)
(13) / LED
(14)
(1)
(2)
(3)
(4)
DC
(5)
(6) EN/IEC
EMC
class A
J
a)
b)
24
e) a) d)
C
OFF
ON
ON
OFF
ON
OFF
C
[mm]
A
P2CF-08, P2CF-11
P3G-08, P3GA-11
A
H3CR-F8(N)
H3CR-F(N)
● (OFF
*1 -F
*2 (OFF)
*3 (ON)
● (ON
*1 -FN
*2 (OFF)
*3 (ON)
J
DC12V 90 110
0.1s
2VA 1.6W
1.3VA 1.1W
0.8W
0.2W
cosφ 1
J
10
LED/
J
20
c) d)
J
OFF
ON
ON
OFF
ON
OFF
J
A
―
P2CF-08, P2CF-11
P3G-08, P3GA-11
H3CR-F8(N)
H3CR-F(N)
J
●Flicker OFF start
*1 Pin No. of -F type
*2 OFF indicator
*3 ON indicator
●Flicker ON start
*1 Pin No. of -FN type
*2 OFF indicator
*3 ON indicator
J
Delayed contacts
Operating power
UK/USA
Rated supply voltage • 100 to 240 VAC (50/60 Hz)/100 to 125 VDC
• 24 to 48 VAC (50/60 Hz)/12 to 48 VDC
Operating voltage range
85% to 110% of rated supply voltage (90% to 110% at 12 VDC)
Power reset Minimum : power-opening time 0.1 s
Power consumption
• 100 to 240 VAC/100 to 125 VDC(When at 240 VAC, 60 Hz)
Relay ON: approx. 2.0 VA (1.6 W)
Relay OFF: approx. 1.3 VA (1.1 W)
• 24 to 48 VAC/12 to 48 VDC(When at 24 VDC)
Relay ON: approx. 0.8 W
Relay OFF: approx. 0.2 W
Reset voltage : 10% max. of rated supply voltage
Control outputs (Time limit contacts): 5 A at 250 VAC / 30 VDC
0.15 A at 125 VDC
resistive load (cosφ = 1)
Minimum load: 10 mA at 5 VDC (P level, reference value)
Ambient temperature • Operating: −10°C to 55°C (with no icing)
• Storage: −25°C to 65°C (with no icing)
Ambient humidity Operating: 35% to 85%
Precautions for Safe Use
UK/USA
Please comply strictly with the following instructions which are intended to ensure safe operation of the controller.
(1) Make sure the proper product is specified for the application.
(2) For correct use, do not subject the timer to the following conditions.
• Dramatic temperature fluctuations
• High humidity or where condensation may occur
• Severe vibration and shock
• Where excessive dust, corrosive gas, or direct sunlight may be present
• Where there is danger of splashing of water, oil or any chemicals
(3) Store the Timer within the rated ranges given for the Timer model you are using. If the Timer is stored below −
10°C, allow it to warm up for three hours at room temperature before turning ON the power supply.
(4) Mounting the Time Switch side-by-side may reduce the life expectancies of internal components.
(5) Use the Timer within the ambient operating temperature and ambient operating humidity ranges given for the
Timer model you are using.
(6) Separate the Timer from any sources of excessive static electricity, such as forming materials and pipes carrying
power or liquid materials.
(7) Maintain the variations in the power supply voltage to within the specified allowable range.
(8) If a voltage that exceeds the rating is applied, internal components may be destroyed.
(9) Wire all terminals correctly.
(10) Do not wire the terminals which are not used.
(11) Install and clearly label a switch or circuit breaker so that the operator can quickly turn OFF the power supply.
(12) The exterior of the Timer may be damaged by organic solvents(such as thinners or benzene), strong alkali, or
strong acids.
(13) Confirm that the power and output indicators are operating normally. Depending on the operating environment,
the indicators and plastic parts may deteriorate faster than expected, causing the indicators to fail. Periodically
perform inspections and replacements.
(14) When disposing of the Timer, observe all local ordinances as they apply.
(15) When using the Timer in an area with excessive electronic noise, separate the Timer and input device as far as possible
from the noise sources. It is also recommended to shield the input signal wiring to prevent electronic interference.
(16) Cleaning
Do not use paint thinner or the equivalent. Use standard grade alcohol to clean the product.
(17) Do not change the time unit and time range while the Timer is in operation, otherwise the Timer may malfunction.
Be sure to turn off the power before changing the setting.
(18) Power supply connection
Use a DC power supply having a ripple factor of 20% or less and supplying a mean voltage that is within the
rated operating voltage marked on the timer.
Make sure that the supply voltage is applied to the timer all at once, using contacts such as of a switch or relay.
Otherwise, the timer may not be able to perform power reset or its set time may be up when it should not.
(19) Interlock the power to the timer with a relay so that the timer will not be left in a time-up condition for long
periods. Leaving the timer in a time-up condition for a month or longer, especially in places with high
temperatures, may result in deterioration to internal parts, such as an electrolytic capacitor.
(20) EN/IEC Standard Compliance
• Refer to the datasheet for the H3CR for cable selection and other conditions for compliance with EMC
standards.
• This is a class A product. In residential areas it may cause radio interference, in which case the user may be
required to take adequate measures to reduce interference.
• There is basic insulation between the power supply terminals and output terminals.
• If double or reinforced insulation is required, use the double or reinforced insulation defined in IEC 60664 that
IEC60664
is suitable for the maximum applied voltage for the clearance, solid insulation, and other factors.
Suitability for Use
UK/USA
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the
combination of the products in the customer's application or use of the product. Take all necessary steps to
determine the suitability of the product for the systems, machines, and equipment with which it will be used. Know
and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCTS FOR AN
APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS
PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR
SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Nomenclature
UK/USA
OFF Indicator (green)
ON Indicator (orange)
Rated time selector
ON time unit selector
Setting dial for OFF (green pointer)
Setting dial for ON (orange pointer)
OFF time unit selector
Note: If pointer is turned
counterclockwise until overranged,
instantaneous output will be issued.
Dimensions
UK/USA
A Panel cutout dimensions
Applicable socket
Model P2CF-08, P2CF-11
Front connection socket
Model P3G-08, P3GA-11
Back connection socket
H3CR-F8(N)
H3CR-F(N)
Timing charts
UK/USA
Connections
UK/USA
Rating