Veracity LONGSPAN VLS-1P-B Quick Start Manual

LONG RANGE ETHERNET & POE
(OPTIONAL)
POWER
SUPPLY
POE
POWER
POWER OVER ETHERNET
|
LONGSPAN can deliver an unrestricted
full-duplex 100Base-TX connection
over 820m of Cat6 or over 600m of
Cat5e network cable.
On Cat6 cable, 25W of POE can be
delivered at 600m or 15W at 800m.
A 10Base-T connection can be
achieved up to 1050m on Cat6.
See LONGSPAN datasheet for details.
| LONGSPAN is fully self-configuring,
featuring remote diagnostic LEDs and
extended temperature rating -40ºC to 70ºC.
POWER INPUT
| The Base unit (VLS-1P-B) may be
powered by either POE-in or by an
external Veracity 57V DC power supply
(VPSU-57V-800).
| POE-in is provided by a POE network
switch or by a POE injector.
| When using the external 57V DC PSU,
it is essential to observe the correct
polarity on the green 2-pin screw
POE POWER BUDGET
|
The Veracity 57V DC PSU will provide
maximum range and POE power
budget at the camera end.
| POE-in is not applicable as a power
source when higher-power POE cameras
are installed, i.e. 802.3at (POE Plus)
25 watt devices. In these cases, the
Veracity 57V DC PSU should be used.
INSTALLATION NOTES
| Standard Cat5e or Cat6 cable and
RJ45 connectors should be used.
| LONGSPAN supports both patch and
crossover cables. Patch wiring (straight
through connection) is recommended.
| LONGSPAN extended network link
set-up and configuration is fully automatic.
| LONGSPAN may also be used with
other twisted pair cables* as follows:
4-pair cable: 10Base-T /100Base-TX with
POE with standard Cat5e / Cat6 pin-out.
2-pair cable: 100Base-TX performance
can be achieved with POE on 2 pairs,
where pins 1 & 2 are used for data and
pins 7 & 8 are used for POE.
1-pair cable: 10Base-T/100Base-TX
performance can be achieved on 1pair,
where pins 1 & 2 are not crossed-over.
This Device Complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
VLS-1P-B
1
1 2 3 SURGE PROTECTION DEVICES RECOMMENDED FOR LONG OUTDOOR NETWORKS
VLS-1P-B, VLS-1P-C
QUICK START GUIDE
2
820M ON CAT6
SURGE PROTECTION
| Any LONGSPAN network design
for outdoor or external sections
must incorporate the appropriate level
of surge protection to avoid invalidation of
warranty due to electrical storm damage.
It is the responsibility of the system
installer to ensure the correct level of
surge protection.
See also surge protection statement below
and LONGSPAN Application Notes.
terminal connector. The correct polarity
is shown on the product top label.
Note that LONGSPAN will automatically
disable the POE-in function when an
external PSU is connected.
| Optionally, the Veracity 57V DC PSU
may be used to locally power LONGSPAN
at the Camera end in order to provide
maximum POE Plus power output to
the camera whatever the LONGSPAN
connection distance.
LARGER SYSTEMS
|
For high channel count or high-density
applications, LONGSPAN Base units
may be rack-mounted in the VLS-1U
fascia plate to support up to 24 units
in 1U. (See LONGSPAN datasheet).
|
Veracity 57V DC rackmount power
supplies are available for larger installations
with multiple base devices.
| LONGSPAN Ethernet ports should be
connected to 100Base-TX or 10Base-T
Ethernet compatible equipment.
| LONGSPAN extended network ports
should only be connected to other
LONGSPAN extended network ports.
Devices are always used in pairs.
| VLS-1P-B supports POE-in (unless
powered externally). VLS-1P-C supports
POE out (to compatible devices).
| When connecting LONGSPAN on cables
over 600m or over cables with four or
more joins (couplers, outlets, patch
panels) on-site testing is recommended.
*Stated performance will be achieved where
twists/metre and cable length permits,
otherwise LONGSPAN will default to
10Base-T performance.
| Please refer to your regional Veracity
Technical Support team for help & advice.
See Application Notes for more details on
www.veracityglobal.com
Surge Protection
All Veracity products have been independently tested to verify their
resilience to the stringent immunity levels of international standards.
Users should note that no electronic equipment can be guaranteed
to be completely protected at levels beyond the defined standard ;
therefore product warranty cannot include damage to products
which has been caused by surges exceeding those of the standards
specified, for example lightning strike activity.
It is the user's responsibility to implement relevant surge protection
measures, as appropriate to the installation. This may include the
fitting of additional surge protection devices where required.
©
Veracity UK Ltd 2019
QSG WV1.5EN
LONGSPAN is a trademark of Veracity UK Ltd
LONG RANGE ETHERNET & POE
LONG
SPAN
VLS-1P-C
3
UP to 25W POE