Related Manuals for Mikado LOGO 800
Summary of Contents for Mikado LOGO 800
- Page 1 Manual LOGO 800 Mikado Model Helicopters GmbH • Graf-von-Schwerin-Str.40 • 14469 Potsdam • Germany phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de © Mikado Model Helicopters GmbH 2019, V1.0...
- Page 2 (model size LOGO 400 to LOGO 600, for example). You are required to adhere to the safety instructions of this manual. In our rigorous testing we fl ew the Logo 800 in very aggressive maneuvers and did not fi nd it to be susceptible to failure, or boom strikes.
- Page 3 17 mm 17 mm M2x10 Elevator Rudder M2,5x8 Ø6 Ø4,8 M2,5x6 15x21x4 M2,5x6 5,5x59 Select the corresponding mounting plate, depending on your servo (10 or 11 mm distance between holes). Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 3...
- Page 4 2.5 mm hex lock nuts in the right hand side frame. 2,5x60 M2,5x6 M2,5x10 8x M2,5 Stop Be sure to instert the adapters at this stage. M2,5x10 M2,5x12 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 4...
- Page 5 Fix the end caps with glue inside the landing skids. 4x60 M3x22 M3x22 3x5x4 M3 Stop 3x5x10 M3x10 M2,5 Stop 2,2x6,5 M3 Stop M3x22 M3 Stop M3x10 M3 Stop M3x12 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 5...
- Page 6 1 Chassis Bag 1 M3x10 M3x20 M3x10 M3x20 M3x10 Only tighten the M3x20 screw once you have mounted the tail boom support. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 6...
- Page 7 Fix servo wire to the bottom side of the servo casing using electrical tape or scotch tape. M3x12 17 mm 17 mm (2x) Roll links/ Roll rechts/ Aileron left Aileron right Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 7...
- Page 8 fl exible extension, to easily mount the 4x26 mm bolt in the tail gear. When mounted properly, the main gear has approx. 1 mm axial play. M2,5x25 (4x) 4x26 Loctite M3x10 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 8...
- Page 9 3) There must be next to no backlash between main gear and pinion. Check the gear mesh after the fi rst couple of fl ights. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 9...
- Page 10 You can distinguish the two disks by sliding 3x6x2,5 them (temporarily) onto the 5 mm tail spindle. Only the disk with the smaller inner diameter will sit tightly. 5x36 3x5x0,5 M3x8 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 10...
- Page 11 Shrink tubing M3x16 Apply grease to the o-rings. 5 min Epoxy Sand carbon Carbon tail rotor push rod tube before glueing the ball link adapters in place. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 11...
- Page 12 fi rmly, making sure the drilled holes for the rotation prevention in the tail boom are aligned properly. Finally fi x the tail boom using the M3x10 hex screws, from both sides. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 12...
- Page 13 Tail Control Rod Guide will M3 Stop clamp too much and pinch the tail control rod guide not allowing it to move freely. Important Mount the ball links 90° to each other. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 13...
- Page 14 Note when mounting the ball links: One side of the ball link will clip on easily. The 4x7x0,8 other one is too tight to clip on easily. The brand name Gabriel must point outwards. M3x47 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 14...
- Page 15 5x24x2 6x12X1,5 M6x12 M3x12 Use the stock washer from Larger inner Ø Smaller inner Ø the rotor blade box.. Please apply grease here Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 15...
- Page 16 Tighten and secure the M4x25 screw in the main rotor head, the M3x30 in the blade holders and the M3x25 in the swash plate driver after mounting and adjusting the rotor head and the linkages. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 16...
- Page 17 Please apply the fabric tube and the edge guard provided in this kit. Both types of protection are also available individually from Mikado. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 17...
- Page 18 Before each fl ight make sure that the battery plate is secured with both quick release mechanisms. Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 18...
- Page 19 14 Canopy and Overview Canopy Mounting The Canopy of the Logo 800 is very large, and therefore requires four mounting points, rather then the standard two mounting points. The 2 extra mounting points in the front ensure that the canopy mounts fi...
- Page 20 15 Overview Spare Parts Mainframe 5354 5015 5353 4517 5022 4515 4521 5020 5332 5021 4523 4601 4517 4522 4521 5022 4524 5017 4099 5018 5055 4516 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 20...
- Page 21 15 Overview Spare Parts Mainframe 4589(Set) 5371 1940 4469 5026 (3x) 4512 5023 1972 5027 (13 Zähne/ Teeth) 4711 5028 (14 Zähne/ Teeth) 5025 5333 5360 1953 5016 5113 5113 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 21...
- Page 22 15 Overview Spare Parts Mainframe 5034 4915 5032 5035 4099 4099 5033 4290 5336 black 4915 5337 white 5353 5053 4554 black 1954 5338 white 5339 black 5340 white Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 22...
- Page 23 16 Overview Spare Parts Tail Boom 4562 5345 5037 5342 5343 5344 5341 5348 (x4) 5347 (Set) Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 23...
- Page 24 17 Overview Spare Parts Tail Rotor 5349 M2,5x12 4581 M2,5x12 M3x12 4567 M3x20 4522 M2,5x8 4566 4524 M3x10 4584 M2,5x16 5351 5352 4583 4571 M2,5x12 4570 5350 4568 2470 2470 M3x8 4582 4569 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 24...
- Page 25 18 Overview Spare Parts Rotor Head 4049 4508 4703 5048 5051 5047 4706 1956 2079 4705 4599 4702 4509 4507 1954 5049 1981 Manual LOGO 800 - ©Mikado Model Helicopters GmbH - Page 25...
Need help?
Do you have a question about the LOGO 800 and is the answer not in the manual?
Questions and answers