Related Manuals for Worx WX531 Series
Summary of Contents for Worx WX531 Series
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 20V Cordless Brushless WX531 WX531.X Circular saw...
- Page 3 PRODUCT SAFETY you are tired or under the influence of drugs, alcohol or medication. A moment of GENERAL POWER TOOL inattention while operating power tools may SAFETY WARNINGS result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective WARNING: Read all safety warnings, equipment such as dust mask, non-skid safety instructions, illustrations and...
-
Page 4: Further Safety Instructions For All Saws
e) Maintain power tools and accessories. 6) Service Check for misalignment or binding of Have your power tool serviced by a moving parts, breakage of parts and any qualified repair person using only identical other condition that may affect the power replacement parts. -
Page 5: Cut-Off Machine Safety Warnings
the kerf closing down, the blade stalls and the motor saw is accidentally dropped, the lower guard reaction drives the unit rapidly back toward the may be bent. Raise the lower guard with the operator; retracting handle and make sure it moves freely and does not touch the blade or any other part, —... -
Page 6: Kickback And Related Warnings
running faster than their rated speed can break The spinning wheel may grab the surface and and fly apart. pull the power tool out of your control. d) Wheels must be used only for n) Do not run the power tool while carrying recommended applications. -
Page 7: Additional Safety Rules
Large workpieces tend to sag under n) Recharge only with the charger specified their own weight. Supports must be placed by WORX. Do not use any charger other under the workpiece near the line of cut and than that specifically provided for use with near the edge of the workpiece on both sides of the equipment. - Page 8 SYMBOLS Wood To reduce the risk of injury, user must read instruction manual Metal Warning Aluminium Wear ear protection Plastic Wear eye protection Abrasive cutting disc Wear dust mask HCS blade Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem.
- Page 9 1 2 3 20V Cordless Brushless WX531 WX531.X Circular saw...
- Page 10 20V Cordless Brushless WX531 WX531.X Circular saw...
- Page 11 20V Cordless Brushless WX531 WX531.X Circular saw...
- Page 12 20V Cordless Brushless WX531 WX531.X Circular saw...
- Page 13 20V Cordless Brushless WX531 WX531.X Circular saw...
- Page 14 20V Cordless Brushless WX531 WX531.X Circular saw...
-
Page 15: Component List
COMPONENT LIST TECHNICAL DATA Type WX531 WX531.X (5- designation of ma- SAFETY SWITCH chinery, representative of Saw) ON/OFF TRIGGER WX531 WX531.X** SOFT GRIP HANDLE Voltage Max*** HEX KEY BLADE GUARD LEVER Rated speed 6900/min BLADE GUARD No load speed 6900/min BASE PLATE 120mm 24T TCT... -
Page 16: Noise Information
NOISE INFORMATION maintained. The use of the correct accessory for the tool and (CUTTING WOOD/CUTTING ensuring it is sharp and in good condition. The tightness of the grip on the handles and if any METAL) anti vibration and noise accessories are used. And the tool is being used as intended by its design and these instructions. -
Page 17: Working Hints For Your Tool
Safety switch and On/Off This tool may cause hand-arm vibration trigger syndrome if its use is not adequately WARNING: To avoid managed cutting injury from the WARNING: To be accurate, an estimation of sharp blade, please don’t put exposure level in the actual conditions of use See Fig. -
Page 18: Troubleshooting
facility. Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. -
Page 19: Declaration Of Conformity
DECLARATION OF CONFORMITY Positec Power Tools (Europe) Ltd, PO Box 6242, Newbury, RG14 9LT, UK Declare that the product, Description Battery-powered circular saw Type WX531 WX531.X (5- designation of machinery, representative of Saw) Function Cutting various materials with a rotating toothed blade Complies with the following directives, 2006/42/EC 2014/30/EU... - Page 20 After-sales Service and Application At www.worx.com you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: 0345 202 9679 E-Mail: customerservices@worxtools.com www.worx.com Copyright © 2020, Positec. All Rights Reserved. AR01490700...
Need help?
Do you have a question about the WX531 Series and is the answer not in the manual?
Questions and answers