Advertisement
Memcom
Telephone
Installation Guide
Ref No. 453 901AU (GB) Version 4
+
Emergency
+
Simple wiring for quick installation
+
Integrated LCD display shows you what you have
programmed
+
All code based programming replaced by a simple tick
box system
+
Flexible installation location and communication
options
Advertisement
Related Manuals for AVIRE Memco Memcom+
Summary of Contents for AVIRE Memco Memcom+
- Page 1 Memcom Emergency Telephone Installation Guide Ref No. 453 901AU (GB) Version 4 Simple wiring for quick installation Integrated LCD display shows you what you have programmed All code based programming replaced by a simple tick box system Flexible installation location and communication options...
-
Page 2: Table Of Contents
Memcom Emergency Telephone Contents Page Page(s) Installation Quick Start Programming Testing and Operating Full Programming Options 8-14 Troubleshooting 15-16 Old Programming Mode System Components Cable Housing Terminal Block External Microphone Memcom Unit Make sure that the unit you have is the right type of unit for the installation. Product codes are below:- 453 011AU - MEMCOM autodialer, 24/230V, (TOC) - Page 3 TOC – Top Of Car Version 453 011AU 1. Using the screws provided, install the Memcom unit to the top of the lift car. The rubber feet must not be removed as this can create feedback. 2. Connect the telephone line, the lift alarm push button and any required accessories as per the wiring diagrams shown on Page 4 of this guide.
- Page 5 Dual Illuminated Alarm Push The diagram below details the wiring required for a dual illuminated alarm push. Connection to the 12VDC supply from the Memcom is shown below.
- Page 6 Australia Default Programming The following pages detail the full programming menu options for the Memcom Emergency Telephone. Memcom is supplied with certain standard factory programming settings, specifically tailored for the Australia and New Zealand lift industries. A description of these settings is provided below. Under ‘Settings >...
-
Page 7: Quick Start Programming
Quick Start Programming Quick Start Guide Quick Start Process Guide Entering Programming Mode The first time the Memcom unit is powered up, it will automatically load the Quick Start menu, which is mapped out here… Menu Controls Scroll up Scroll Down Forward / Accept Back / Cancel S imply follow the quick start guide... -
Page 8: Testing And Operating
Testing and Operating Mode 1. Programming The status of the unit is shown on the top row of the idle screen. If there are no faults, it will display ‘Status OK’. Press 1 to access the standard programming menu Old Programming Mode– to program the Memcom unit using the Old Menu and code based programming options, simply press * followed by the passcode for the unit and confirm by pressing # (default- *1234#) from the... -
Page 9: Full Programming Options
Full Programming Options Menu Sections Quickstart > Quick Start Tel. Numbers > The quick start menu consists of 7 menu options required for quick Alarm no. 1 setup. Please refer to the previous page in this guide for more Alarm no. 2 information. - Page 10 Tech IP2 delay the second number and so on. Hangup delay Ext. mic. record Only use if directed by Avire Technical Answer delay Support Alt. dial tone Allows system to work with an Messages >...
- Page 11 Full Programming Options Menu Sections continued... Quickstart > Tel. Numbers > Settings Alarm no. 1 Systems Config+ Alarm no. 2 System Config+ > Alarm no. 3 Alarm no. 4 Auto Location When an operator answers an alarm call, the Memcom will automatically Tech.no.
- Page 12 Full Programming Options Menu Sections continued... Quickstart > Lift Monitor Tel. Numbers > The lift monitor section allows you to detect faults from third party Alarm no. 1 lift monitoring devices connected to the technical inputs on the Alarm no. 2 Memcom unit.
- Page 13 Full Programming Options Menu Sections continued... Quickstart > Tel. Numbers > Messages Alarm no. 1 Messages > Alarm no. 2 Location This is the only message that needs Alarm no. 3 recording. The location message is played to the call centre receiving the alarm call, Alarm no.
- Page 14 Full Programming Options Menu Sections continued... Quickstart > Advanced Settings continued... Tel. Numbers > Alarm no. 1 Relay Mode Alarm no. 2 The relay contact on a Memcom can be used to switch the power Alarm no. 3 supply to an external device. The following modes are available: Alarm no.
- Page 15 GMT Offset Messages > Will not need updating on the unit. For reference only. Location DTMF RX Reassurance Guidance Use only if directed by Avire Technical Support. Time / Date > Time Date Advanced > Passcode Network ID Next EN81 call...
-
Page 16: Troubleshooting
Troubleshooting Telephone Line Problem Solution “No Dial Tone” showing on LCD 1. Disconnect Green Terminal Block and check voltage across Terminals 1&2 (24VDC~60VDC dependent on the type of line used). 2. If no voltage is present, check the telephone socket and the travelling spares/flex used. “Number is not Recognised”... - Page 17 Battery Specification • 12V, 0.8Ah, Lead Acid battery • Only use Avire batteries with the Memcom Emergency Telephone (battery part number 450 880-04) Replacing the Battery Disconnect the power from the Memcom , wait 5 seconds and then press and hold the # key to power down the unit...
-
Page 18: Old Programming Mode
*021# Exit programming and call Alarm number 1 only *035# Exit programming and call Alarm Number 5 Technical Alarm Avire Global Pte Ltd Unit 16 296691102 269631137 69-73 O’Riordan Street sales.au@avire-global.com Alexandria www.memco-global.com NSW 2015 Memco is a brand of Avire www.avire-global.com...
Need help?
Do you have a question about the Memco Memcom+ and is the answer not in the manual?
Questions and answers