Fluke 114 User Manual
True-rms multimeters
Hide thumbs
Also See for 114:
- User manual ,
- Calibration information manual (21 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fluke 114
Summary of Contents for Fluke 114
- Page 1 ® 114, 115, and 117 True-rms Multimeters Users Manual PN 2572573 July 2006, Rev. 1, 2/07 © 2006, 2007 Fluke Corporation, All rights reserved. Printed in China All product names are trademarks of their respective companies. MyFlukeStore 1.888.610.7664 www. .com...
-
Page 2: Limited Warranty And Limitation Of Liability
LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This warranty does not cover fuses, disposable bat- teries, or damage from accident, neglect, misuse, alteration, contamination, or abnor- mal conditions of operation or handling. - Page 3 True-rms Multimeters Introduction Unsafe Voltage The Fluke Model 114, Model 115, and Model 117 are To alert you to the presence of a potentially hazardous voltage, the Y symbol is displayed when battery-powered, true-rms multimeters (hereafter "the the Meter measures a voltage ≥30 V or a voltage Meter") with a 6000-count display and a bar graph.
- Page 4 Only use test leads that have the same voltage, category, and amperage ratings as the meter and that have been approved by a safety agency. • Remove test leads from Meter before opening the battery door or Meter case. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
-
Page 5: Safety Information
Check the test leads for continuity before use. Do not use if the readings are high or noisy. • Do not use the Auto Volts function to measure voltages in circuits that could be damaged by this function’s low input impedance (≈3 kΩ)(114 and 117 only). Symbols AC (Alternating Current) - Page 6 The Meter function is set to Diode Test 115 & 117 Input is a negative value. 114, 115, & 117 X Unsafe voltage. Measured input voltage ≥30 V, or voltage 114, 115, & 117 overload condition (OL). MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 7 W The input is too large for the selected range. 114, 115, & 117 W Test lead alert. Briefly displayed whenever the Meter’s LEAd 115 & 117 function switch is rotated to or from any A position. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 8 Calibration required. Meter calibration is required before the Meter will operate. EEPr Err Internal error. The Meter must be repaired before it will operate. F11 Err Internal error. The Meter must be repaired before it will operate. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
-
Page 9: Rotary Switch Positions
>10.00 A display flashes. >20 A, OL is displayed. Non-contact sensing of ac voltage. Note: All ac functions and Auto-V LoZ are true-rms. AC voltage is ac-coupled. Auto-V LoZ, AC mV and AC amps are dc-coupled. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:... - Page 10 • To exit and erase stored readings, press • In the Manual Range mode, you override Autorange and for at least one second or turn the rotary switch. select the range yourself. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
-
Page 11: Power-Up Options
Meter on. lead before removing the common test lead. Power-Up Options are canceled when you turn the Meter off and when sleep mode is activated. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:... - Page 12 Meter, disconnect shorts. For maximum accuracy in making circuit power and discharge all high- resistance measurements, use the Meter’s voltage capacitors before testing resistance (e) function. resistance, continuity, diodes, or capacitance. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
-
Page 13: Making Basic Measurements
Measuring AC and DC Millivolts Millivolts AC Millivolts DC edy03f.eps Using Auto Volts Selection (114 & 117 only) With the function switch in the x position, the Meter edy18f.eps automatically selects a dc or ac voltage measurement based on the input applied between the V or + and COM jacks. - Page 14 A (Amps) terminals. Turn circuit power off, break the circuit, insert the Meter in series with the circuit, and then turn circuit power on. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 15 Meter. Make sure the Meter has the correct function selected, AC or DC, for your current probe. Refer to a Fluke catalog or contact your local Fluke representative for compatible current clamps. edy05f.eps edy14f.eps...
- Page 16 The Meter measures the frequency of a signal by counting the number of times the signal crosses a trigger level each second. The trigger level is 0 V, 0 A for all ranges. edy13f.eps MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 17 Capacitance mode. In this mode, capacitance Open measurements will have a lower accuracy and lower Shorted dynamic range. This setting is not saved when the Meter is edy07f.eps turned off or goes into sleep mode. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 18 0, 15, 30, 45, and 60 V. An input of −30 V turns on the negative sign and the segments edy10f.eps up to the middle of the scale. aej11f.eps MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
-
Page 19: Maintenance
Do not attempt to install the battery directly into the case. 5. Install and tighten battery door screw. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:... - Page 20 5. Remove the fuse from its holder and replace it with an 11 A, 1000 V, FAST fuse having a minimum interrupt rating of 17,000 A. Use only Fluke PN 803293. 6. To re-assemble the Meter, first attach the case bottom to the case top, then install the two screws.
-
Page 21: General Specifications
Surge Protection ............. 6 kV peak per IEC 61010-1 600V CAT III, Pollution Degree 2 W Fuse for A input (115 & 117 only): ....11 A, 1000 V FAST 17 kA Fuse (Fluke PN 803293) Display ..............Digital: 6,000 counts, updates 4/sec Bar Graph: 33 segments, updates 32/sec Temperature............. - Page 22 2.0 % + 3 115, 117 6.000 V 0.001 V 114, 2.0 % + 3 1.0 % + 3 C Volts True-rms 60.00 V 0.01 V 115, 117 600.0 V 0.1 V MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 23 100 μF - 1000 μF: 1.9 % + 2 > 1000 μF: 5 % + 20 Lo-Z Capacitance 115, 117 1 nF to 500 μF 10% + 2 typical (Power-up option) MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 24 [2] AC Volts Hz is ac-coupled and specified from 5 Hz to 50 kHz. AC Amps Hz is dc-coupled and specified from 45 Hz to 5 kHz. [3] >10 A unspecified. MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 25 Full Scale Voltage Current <350 μA Ohms <2.7 V dc To 6.0 MΩ 40 MΩ <0.7 V dc <0.9 V dc Diode Test <2.7 V dc 2.000 V dc <1.2 mA MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
- Page 26 114, 115, and 117 Users Manual MyFlukeStore 1.888.610.7664 www. .com Shop for Fluke products online at:...
Need help?
Do you have a question about the 114 and is the answer not in the manual?
Questions and answers