TP-Link CPE210 Installation Manual
Outdoor cpe
Hide thumbs
Also See for CPE210:
- Installation manual ,
- User manual (141 pages) ,
- How to upgrade the firmware (5 pages)
Related Manuals for TP-Link CPE210
Summary of Contents for TP-Link CPE210
- Page 1 Installation Guide Outdoor CPE Get Started with Setup Videos Scan the QR code or visit https://www.tp-link.com/support/setup-video/...
-
Page 3: Table Of Contents
Contents Overview Hardware Connection Site Consideration Connection and Installation Lightning & ESD Protection Logging in to the PharOS... -
Page 4: Overview
Overview TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless Pole Mounting Power Cord Straps Installation Guide Outdoor CPE Need setup videos? Scan the QR code or visit https://www.tp-link.com/en/support/setup-video/ Mounting Bracket Pharos CPE Passive PoE Installation Guide Adapter • LED Explanation AP/AP Router Mode: All four LEDs remain solid. - Page 5 • Panel Layout Grounding Shielded Ethernet Shielded Ethernet RESET Terminal Port LAN0 (Passive Port LAN1 PoE IN) RESET Grounding Shielded Ethernet Port Terminal LAN (Passive PoE IN)
- Page 6 Passive PoE Adapter: Power LED Press and hold for about 8 seconds The Power LED is on when the until CPE’s LEDs of wireless signal passive PoE adapter is working normally.
- Page 7 Application Example The CPE device(CPE210 CPE220 CPE510) provides outdoor network access over long distances for point-to-point applications.
-
Page 8: Hardware Connection
Hardware Connection 1. Site Consideration Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like height of the devices. Line of Sight Side View... - Page 9 • Orientation Install the CPE devices with the front facing the intended signal receiving GPS and some landmarks according to the horizontal beamwidth listed below. Models Horizontal Beamwidth shenzhen...
-
Page 10: Connection And Installation
2. Connection and Installation Connect and mount the CPE and power adapter as shown below. The LAN0 Ethernet cable length up to 60m You should prepare an adequate Connect to a computer, Ethernet cable to connect the CPE router or switch. and the passive PoE adapter. - Page 11 have oriented. Follow the steps below to mount the power adapter: recommended to install the adapter with the Ethernet port facing upward. Drill two holes on the wall and insert the plastic wall anchors into the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward.
-
Page 12: Lightning & Esd Protection
3. Lightning & ESD Protection connection and the provided PoE adapter (method 1 CPE to earth ground through grounding cable (method Two Methods: Shielded CAT5e (or above) Cable with Ground Wire Grounding Terminal and Cable Grounding Terminal Grounding Cable Grounded 3-wire Power Outlet Shielded CAT5e (or above) Cable with Ground Wire... - Page 13 Sheath Twisted Pair Ground Wire Cable Shield Secondary Cable Shield Shielded RJ45 Connector...
-
Page 14: Logging In To The Pharos
This chapter introduces the login to the PharOS Web Interface and the 1. Logging in to the PharOS and press Enter return... - Page 15 Enter for both and Password. Read and agree the Change the default User Name and Password to protect your CPE. download the User Guide of Pharos products in the download center.
- Page 16 The typical topology is as follows. A wireless bridge is built between two locations that are far from each other. Follow the instructions below to IP Camera Computer Access Point Client LAN: 192.168.0.254 LAN: 192.168.0.2 Log in to PharOS and go to the Quick Setup page. Operation Mode: Select Access Point and click Next.
- Page 17 click Next. Wireless Client Settings: a. Click Survey then click Connect. b. Select WPA-PSK/WPA2-PSK click Next. Finish: Verify your settings and click Finish to complete the download the User Guide of Pharos products in the download center.
- Page 18 Antenna Alignment Antenna alignment can help you to optimize the antenna signal. To get the list on the upper-right corner and enable Alignment Beep during align- ment. Then adjust your antenna until the sound frequency turns to the lowest. can help you to estimate the signal strength received by the signal strength.
- Page 19 HARDWARE FEATURES Models LAN: 10/100 Mbps LAN0: 10/100 Mbps LAN1: 10/100 Mbps Ethernet Port Interface GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default Passive PoE Adapter Included Power Supply ESD Protection Up to 6 kV to 70 (-40 10% to 90%...
-
Page 20: Faq
Q1. How to restore the CPE to its factory default RESET button on the CPE or the Remote Reset button on the Passive PoE Adapter. Method 1: Via the RESET Button on the CPE RESET Button Press and hold for about 8 seconds until CPE’s LEDs of wireless signal Adapter Press and hold for about 8 seconds until CPE’s... - Page 21 which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this h = the height of H h+r * (1 40%) obstacle at this point (H is the height of the CPE) r = Fresnel zone radius in meters f = operating frequency of the devices in &...
- Page 22 • more stability. • collision. compatible with TP-Link’s Pharos series products. Please notice that you will not be able to connect other Wi-Fi devices to an AP with appropriate channel for the devices? in the tools drop-down will be lost during spectrum analysis. Click Yes to continue to the Spectrum Analysis page.
- Page 23 Community.
- Page 24 Safety Information • • • Do not use damaged charger or USB cable to charge the device. • Do not use any other chargers than those recommended • Do not use the device where wireless devices are not allowed. • Adapter shall be installed near the equipment and shall be easily accessible. Use only power supplies which are provided by manufacturer and in the original Please read and follow the above safety information when operating the device.
- Page 25 Component Name Model I. T .E. Power Supply TL-POE2412G Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America,Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com...
- Page 26 FCC compliance information statement Product Name: I.T.E. Power Supply Model Number: TL-POE2412G Responsible party: TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/ Tel: +1 626 333 0234...
- Page 27 Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
- Page 28 2412MHz—2472MHz(20dBm) (CPE210/CPE220) 5500MHz—5700MHz(30dBm) (CPE510) EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of...
- Page 29 Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement (For CPE220/CPE510) CAN ICES-3 (A)/NMB-3(A) Industry Canada Statement (For CPE210) CAN ICES-3 (B)/NMB-3(B) Korea Warning Statements (For CPE220/CPE510)
- Page 30 NCC Notice & BSMI Notice For CPE510 (For CPE220/CPE510)
- Page 31 Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pur- suant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
- Page 32 GPL Code used in TP-Link products are available to you in GPL-Code-Centre under GPL. ©2019 TP-Link...
Need help?
Do you have a question about the CPE210 and is the answer not in the manual?
Questions and answers