Summary of Contents for Avigilon HD-NVR-ANK2-1
- Page 1 Analytics Kit HD-NVR-ANK2-1 For: NVR Value Series 4 (HD-NVR4-VAL) HD NVR Series 3 (HD-NVR3-VAL, HD-NVR3-STD, HD-NVR3-PRM) HD NVR Series 2 VMA-AS3-ANK For: 16- and 24-Port Video Appliance (VMA-AS3-16P,VMA-AS3-24P)
- Page 2 (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein.
-
Page 3: Table Of Contents
Table of Contents Analytics Kit for NVRs and Video Appliances Installing the Analytics Kit into the NVR4-VAL or HD-NVR3-VAL Installing NVR Analytics Kit into the HD-NVR3-PRM or HD-NVR3-STD Installing the Analytics Kit into the HD-NVR2 Updating and Configuring the NVR for Analytics Updating Windows PowerShell (Windows Server 2012 only) Updating the Windows OS Driver and Configuring the NVR Troubleshooting the NVR Appliance Fans... -
Page 4: Analytics Kit For Nvrs And Video Appliances
Two versions of the Analytics Kit are available: Analytics Kit for NVRs (HD-NVR-ANK2-1 Analytics Kit for Video Appliances (VMA-AS3-ANK) Install the Analytics Kit for NVRs (HD-NVR-ANK2-1) to use the Avigilon Control Center (ACC™) video analytics features on the following Avigilon recorders: Any NVR Value (Series 4) model Any NVR (Series 3) models The NVR (Series 2) - Page 5 4. Install the latest version the ACC software used at your site. NOTE: To make use of the Analytics Kit for an NVR or Video Appliance after it has been configured, you must use the ACC software version 6.8.6.4 or later. Analytics Kit for NVRs and Video Appliances...
-
Page 6: Installing The Analytics Kit Into The Nvr4-Val Or Hd-Nvr3-Val
Installing the Analytics Kit into the NVR4-VAL or HD-NVR3-VAL 1. Make sure the recorder is turned off. All network, power, and peripheral cables are disconnected from the recorder. Use a static mat or static strap to ground yourself against static shock. 2. - Page 7 6. Insert and press the NVR Analytics Kit into the appropriate expansion riser slot. 7. Push the expansion card riser back into place and close the expansion card latch. Installing the Analytics Kit into the NVR4-VAL or HD-NVR3-VAL...
- Page 8 8. Close and lock the recorder cover. 9. Reconnect all the cables and turn on the recorder. 10. Proceed to install the required Windows driver for the NVR Analytics Kit. See Updating the Windows OS Driver and Configuring the NVR on page 16. Installing the Analytics Kit into the NVR4-VAL or HD-NVR3-VAL...
-
Page 9: Installing Nvr Analytics Kit Into The Hd-Nvr3-Prm Or Hd-Nvr3-Std
Installing NVR Analytics Kit into the HD-NVR3-PRM or HD-NVR3-STD 1. Make sure the recorder is turned off. All network, power and peripheral cables are disconnected from the recorder. It is recommended that you use a static mat or static strap to ground yourself against static shock. - Page 10 4. Lift the blue expansion card latch out of the recorder. 5. Remove the slot filler plate in riser 2 - slot 5. 6. Insert and press the Analytics Kit into the appropriate riser slot. The Analytics Kit needs to be installed on riser 2 - slot 5. Installing NVR Analytics Kit into the HD-NVR3-PRM or HD-NVR3-STD...
- Page 11 7. Push the blue expansion card latch back into place. 8. Close and lock the recorder cover. 9. Reconnect all the cables and turn on the recorder. 10. Proceed to install the required Windows driver for the Analytics Kit. See Updating and Configuring the NVR for Analytics on page 15.
-
Page 12: Installing The Analytics Kit Into The Hd-Nvr2
Installing the Analytics Kit into the HD-NVR2 You can install the Analytics Kit in an HD-NVR2 after the recorder has been upgraded to Windows 10. For instructions, download the Windows 10 Operating System Upgrade for Avigilon NVR2 and AS1 Recorders from the Avigilon Technical Support website. - Page 13 3. At the back of the recorder, locate where the Analytics Kit needs to be installed. For HD-NVR2, the Analytics Kit needs to be installed on riser 2 - slot 2 (or the top slot on the riser). 4. Lift the blue expansion card latch out of the recorder. 5.
- Page 14 7. Push the blue expansion card latch back into place. 8. Close and lock the recorder cover. 9. Reconnect all the cables and turn on the recorder. 10. Install the required Windows driver for the Analytics Kit. See Updating and Configuring the NVR for Analytics on the next page.
-
Page 15: Updating And Configuring The Nvr For Analytics
The USB flash drive provided with the NVR Analytics Kit contains verified software to update the Windows operating systems supported on the current range of available Avigilon NVRs. You must install the update software appropriate to the Windows OS on your NVR to automatically configure the NVR Analytics Kit to operate with the Avigilon Control Center software. -
Page 16: Updating The Windows Os Driver And Configuring The Nvr
1. Insert the USB flash drive into the USB port on the NVR. 2. Windows Server 2012R2: a. Navigate to the ../Server2012R2/ folder on the USB drive. b. Double-click on Win8.1AndW2K12R2-KB3191564-x64. Updating the Windows OS Driver and Configuring the NVR Update the driver software for the version of the Windows operating system on your NVR: Updating the Windows OS Driver and Configuring the NVR... - Page 17 The process takes under ten minutes. After it completes the NVR will automatically restart. After the Analytics Kit has been installed and configured, you can download, install and run the latest version of the Avigilon Control Center software. Updating the Windows OS Driver and Configuring the NVR...
-
Page 18: Troubleshooting The Nvr Appliance Fans
Troubleshooting the NVR Appliance Fans On NVR STD or NVR PRM appliances after the NVR Analytics Kit has been installed and configured and the recorder restarted, check the fan speed. Normally, the fan speed should slow down and the fan noise noticeably drop shortly after powering on. -
Page 19: Installing The Analytics Kit Into The 16 Port Or 24 Port Video Appliance
Install the Analytics Kit for the Video Appliance (VMA-AS3-ANK) in any HD Video Appliance Pro 16 Port or 24 Port model to use the video analytics features of the Avigilon Control Center (ACC™) system. The Analytics Kit consists of the GPU preinstalled in a mounting bracket that drops into place in the chassis and is secured in place with four screws. - Page 20 3. The Analytics Kit is installed in the open area towards the back of the chassis next to the internal power supply: a. Remove the round-headed screw (1) from the bottom of the chassis and set aside. b. Place the Analytics Kit into the chassis, ensuring the connector (2) fits securely into the slot (3). c.
-
Page 21: Updating And Configuring The 16 Port Or 24 Port Video Appliance For Analytics
Windows 10 driver you must install on the HD Video Appliance Pro 16 Port or 24 Port model. After it is installed, Avigilon Analytics functionality will be automatically configured on the appliance to operate with the Avigilon Control Center software.
Need help?
Do you have a question about the HD-NVR-ANK2-1 and is the answer not in the manual?
Questions and answers