Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for SRM X-Power
Summary of Contents for SRM X-Power
- Page 1 V1.1...
-
Page 2: Table Of Contents
TABLE OF CONTENT INTRODUCTION .................. PACKAGE CONTENT ................SAFETY / WARNINGS ................. WARRANTY ..................TECHNICAL DATA ................INSTALLATION OF X-POWER ............PEDAL INSTALLATION ..............CHARGING THE PEDALS ............... X-POWER APP DOWNLOAD ............INSTALLATION OF X-POWER PEDALS......... USING X-POWER ................OTHER APP FEATURES .............. -
Page 3: Introduction
This manual provides instructions on features, important safety information and how to set up and use your X-Power pedals. How does the X-Power pedal work? Each pedal measures the force applied and the cadence in real-time then calculates the torque and power, sending it to your bike computer. -
Page 4: Safety / Warnings
They are not designed to release automatically at times such as when falling off the bicycle. If you have any doubt when installing the X-Power pedals, we recommend that you seek assistance from an authorized retailer or refer to the support page on www.srm.de. -
Page 5: Warranty
SRM X-Power PowerMeter pedals are warrantied to be free from defects in materials or workmanship for three years from the date of purchase. Within this period, SRM will, at its option, repair or replace any components that fail in normal use. -
Page 6: Installation Of X-Power
Setting up X-Power pedals is quick and easy. Follow the installation steps outlined below and fully charge both pedals as described on page 8. Install the X-Power app on your cell phone and follow the installation process inside the app properly. -
Page 7: Pedal Installation
PEDAL INSTALLATION Apply grease to the pedal threads. Use a 15 mm open end wrench (width >6 mm) to install the pedals into your crankset. Recommended min. torque 30Nm (22 lbf-ft). The pedal sides are clearly marked with R and L. I NOTE Do not use a cone wrench as it might damage the charging port. -
Page 8: Charging The Pedals
CHARGING THE PEDALS To charge the X-Power pedals attach the magnetic charge adapter to a USB wall charger USB Micro-B cable (not included) with the enclosed USB cable. Connect the adapter onto the charge port on Magnetic charge adapter the pedal shaft. A... -
Page 9: X-Power App Download
X-POWER APP DOWNLOAD To configure and calibrate the pedals download the X-Power application (iOS and Android), enable Bluetooth on the ® phone and spin both pedals to turn them on. You can then follow the on-screen instructions to connect to the app. -
Page 10: Installation Of X-Power Pedals
INSTALLATION OF X-POWER PEDALS Step 1: Step 2: Open the X-Power App and Select the pedal shown! search for your pedals. Make I NOTE sure both pedals are turned Only the right pedal will be shown! on and Bluetooth is enabled. - Page 11 Step 5: Step 6: Zero Load Calibration Choose the correct crank I NOTE length of your crankset. Ensure there is no load on the pedal while performing the offset calibration! Continue with next step when successful. Repeat this step if calibration fails! Step 7: Angle Calibration Step 8: NOTE...
-
Page 12: Using X-Power
USING X-POWER Before the first ride! Spin the X-Power pedals to turn them on and connect to your bike computer. See page 14 on how to pair your pedals to your bike computer. See page 15-16 on how to mount the cleats and adjust the bindings according to your needs. -
Page 13: Other App Features
™ affected. INSTALLATION Guides through the quick installation process of the X-Power pedals to make sure pedals are correctly setup. See page 10-11 for more information on how to install the pedals. REALTIME Realtime tab shows power, torque, and power balance for each pedal independently and the combined values. -
Page 14: Powermeter Pairing
To show data on your device you need to ™ ® pair the X-Power pedal with your device. Depending on the device you might see one or more sensors. Select either Bluetooth or ANT+ to connect your bike computer. -
Page 15: Binding And Cleat
BINDING AND CLEAT Adjust the spring force to the optimal cleat holding force as needed when releasing the cleats from the bindings. The adjustment bolt is located at the rear of each binding. To adjust the spring tension use a 3mm allen key. Clockwise rotation will increase and counter clockwise will decrease the holding force. -
Page 16: Engaging And Releasing The Cleats
ENGAGING AND RELEASING THE CLEATS Engaging the cleats with the pedal Releasing the cleats from the pedal Press the cleats into the pedals with a forward These cleats only release when the heel is and downward motion until the cleat engages twisted outward. -
Page 17: Maintenance
MAINTENANCE To keep the X-Power pedals running smoothly you don’t need to disassemble them. Simply use a dry cloth and wipe away the dirt and debris around the green outer seal. I NOTE Please do not use solvents, as this can damage the seals or other parts inside the pedal, which can lead to further damage. -
Page 18: Troubleshooting / Faq
If the problem persists, Use the X-Power app on your phone to connect to your please contact SRM - the info page of the X-Power app is X-Power pedals. If new firmware is available, you will be helpful for diagnosis. -
Page 19: Declaration Of Conformity
DECLARATION OF CONFORMITY This device has been tested and found to comply with part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. -
Page 20: Contact Us
CONTACT US CONTACT US ► CONTACT US ► SRM GmbH | Rudolf-Schulten-Str. 6 | 52428 Jülich | Germany Version: V1.1 / March 2020 © 2020 SRM GmbH www.SRM.de All copyrights and trademarks are the property of their respective owners...
Need help?
Do you have a question about the X-Power and is the answer not in the manual?
Questions and answers