Advertisement
Quick Links
ASSEMBLY INSTRUCTION, CARE, MAINTENANCE AND USER'S GUIDE
- This product is intended for use by children from ages 3 to 8
- This unit is designed for use by up to 8 children at one time.
Maximum weight of each user is 100 lbs.(45.4kg), with a
combined maximum weight of 800lbs(363kg)
- Assembly requires two adults
WARNING
- Do not allow more than one child to play on the individual
swing/slide at the same time
- Do not allow children to slide down head first.
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
For customer service, please call 1-866-370-2131 Monday-Friday 9:00am-5:00pm Eastern Time
SPORTSPOWER LTD, FLAT M, 3/FLOOR, KAISER ESTATE PHASE 3, 11 HOK YUEN STREET, HUNGHOM, KOWLOON, HK.
8 STATION SWING SET
MODEL # MSC-3990
OWNER'S MANUAL
FOR RESIDENTIAL USE ONLY
DO NOT RETURN TO THE STORE.
or visit our website at www.sportspowerltd.net
Corporate US toll-free number 1-800-497-6106
Advertisement
Related Manuals for SPORTSPOWER MSC-3990
Summary of Contents for SPORTSPOWER MSC-3990
- Page 1 DO NOT RETURN TO THE STORE. For customer service, please call 1-866-370-2131 Monday-Friday 9:00am-5:00pm Eastern Time or visit our website at www.sportspowerltd.net SPORTSPOWER LTD, FLAT M, 3/FLOOR, KAISER ESTATE PHASE 3, 11 HOK YUEN STREET, HUNGHOM, KOWLOON, HK. Corporate US toll-free number 1-800-497-6106...
- Page 2 INTRODUCTION Dear Valued Customer, Congratulations on your Sportspower play set purchase! Please read and completely understand the contents of this owner’s manual. This manual contains specific safety instructions that must be followed to enable safe play and prevent injuries. This play set is for residential use only.
- Page 3 IMPORTANT SAFETY INSTRUCTIONS BEFORE YOU BEGIN: Carefully read all instructions in this manual before assembling and using this product. The unit must be assembled by adults. Heavy duty working gloves must be worn to avoid injuries during assembly. Children must not use the equipment until properly assembled and anchored. Adult supervision is required during the use of this equipment at all times WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLYING OR USING THIS EQUIPMENT...
- Page 4 The following is a list of recommended ground covers from the Consumer Product Safety Commission: SUGGESTED MATERIAL SUGGESTED MATERIAL 9” Double Shredded Bark Mulch Uniform Wood Chips 12” Fine Gravel 12” Fine Sand 12” The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook recommends to install and maintain the playground equipment over at least 9 inches of wood chips, mulch or shredded rubber (for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as shock absorbing material.
- Page 5 REGULAR INSPECTION OF THE EQUIPMENT • DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to ensure the equipment and all parts are well secured and stable before each use. • ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be potentially hazardous to users.
- Page 6 CARE AND MAINTENANCE ANNUAL MAINTENANCE CHECKLIST AT THE BEGINNING OF EACH PLAY SEASON: • Tighten all hardware. • Lubricate all metallic moving parts per manufacturer’s instructions. • Check all protective coverings on bolts, pipes, edges and corners. Replace if they are loose, cracked or missing.
- Page 7 IMPORTANT CONSUMER INFORMATION SHEET The Consumer Product Safety Commission estimates there are about 200,000 playground related injuries involving children each year. Injuries involving this hazard pattern tend to be among the most serious of all playground injuries and have the potential to be fatal, particularly when the injury is to the head. The surface under and around playground equipment can be a major factor in determining the injury-causing potential of a fall.
- Page 8 TOOLS NEEDED Please prepare the following tools prior to assembling this equipment. Special Socket Wrench Tape Measure (Included) (Not included) Hammer Wrench (If you intend to install anchor, this is needed) (Included) Wrench Big Allen Wrench (Included) (Included) Flat Head and Philips Head Screwdriver Middle Allen Wrench (Not included) (Included)
- Page 9 Part list for main frame assembly LEFT TOP BAR MIDDLE TOP BAR RIGHT TOP BAR 8PCS CROSS BAR (WITH TWO HOLES) 3PCS CROSS BAR (WITH FOUR HOLES) END CAP (PRE-ASSEMBLED) 2PCS Hardware used for main frame assembly BOLT 5/16” *2.5” (8MM*64MM) 20PCS NYLON NUT 5/16’’...
- Page 10 Hardware used for flying saucer assembly F1-1 BOLT 3/8” *3.3” (9.5MM*85MM) 4PCS REINFORCING STEEL SPACER 8PCS NYLON NUT 3/8’’ 12PCS 3/8” ARC WASHER 4PCS Bracket used for glide ride assembly BRACKET BRACKET CLAMP REINFORCING STEEL SPACER 2PCS BOLT 5/16” *1” (8MM*25MM) 2PCS NYLON NUT 5/16’’...
- Page 11 Hardware used for glide ride assembly BOLT 1/4” *1.5” (6.5MM*37MM) 4PCS BOLT 1/4’’ *1.7” (6.5MM*43MM) 2PCS SCREW 0.22” *3/4” (5.5MM*19MM) 4PCS J-BOLT 2PCS SPRING WASHER (MEDIUM) 4PCS CAP BOLT 1/4” *5/10” (6.5MM*14MM) 2PCS CAP NUT 1/4” 4PCS NUT 1/4” 2PCS SPRING WASHER (LARGE) 2PCS SPRING WASHER (MEDIUM)
- Page 12 Parts used for rocking horse assembly HORSE PART 1 HORSE PART 2 HORSE PART 3 FRONT LEFT LEG FRONT RIGHT LEG BACK LEFT LEG BACK RIGHT LEG HORSE GRIP TUBE HORSE SEAT HORSE BACK HORSE SUPPORT HORSE FRONT SUPPORT 2PCS BRACKET 2PCS BRACKET CLAMP...
- Page 13 Hardware used for rocking horse assembly BOLT 1/4” *4/5” (6.5MM*20MM) 10PCS BOLT 5/16” 4.2” (8MM*106MM) 4PCS 5/16” WASHER 16PCS NYLON NUT 5/16’’ 20PCS BOLT 5/16” *6.3” (8mm*159MM) 2PCS BOLT 5/16” *6.4” (8MM*162MM) 2PCS BOLT 1/4” *1.2” (6.5MM*30MM) 4PCS 1/4” ARC WASHER 8PCS CAP NUT 1/4”...
- Page 14 Hardware used for slide assembly PLASTIC CONNECTOR 2PCS BOLT 1/4” *1.5” (6.5MM*38MM) 6PCS BOLT 1/4” *5” (6.5MM*127MM) 2PCS SPRING WASHER (LARGE) 4PCS CAP NUT 1/4” 10PCS CAP BOLT 1/4” *1/2” (6.5MM*14MM) 4PCS SPRING WASHER (MEDIUM) 20PCS BOLT 1/4” *3” (6.5MM*75MM) 6PCS...
- Page 15 ASSEMBLY INSTRUCTIONS Place the playground equipment on level ground and not less than 6ft (1.8m) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry line, or electrical wires. Do not install the playground equipment over concrete, asphalt, packed earth, or any other hard surface;...
- Page 16 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 1 Insert A1 into A2 as shown below and secure with B1, B5, B4 and B3.
- Page 17 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 2 ...
- Page 18 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 4 Slide the small end of R4 into the pocket of R7.
- Page 19 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of F1-1 each step and went back to tighten all of the nuts and bolts. STEP 5 F1-1 Attach R8 and R3 to A1.
- Page 20 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 7 ...
- Page 21 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. Glide Ride Assembly STEP 8 ...
- Page 22 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 10 ...
- Page 23 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 12 ...
- Page 24 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. Swing seats assembly STEP 13 ...
- Page 25 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. Rocking Horse assembly STEP 15 ...
- Page 26 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 16 ...
- Page 27 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 18 ...
- Page 28 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 19 Put the body of the horse onto H11.
- Page 29 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. D12-1 STEP 21 D12-1...
- Page 30 STEP 22 Insert H16A (which is pre-assembled with H15) into the holes of R3. Secure using D10 and D4. H16A H16A H16A H16A...
- Page 31 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 23 ...
- Page 32 NOTE: 1. Do not over-tighten the nuts and bolts at every step. 2. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. Slide assembly STEP 24 ...
- Page 33 STEP 25 Attach X6 to X1-N and X2-N. Secure each side using Z1, Z6 and Z4. Attach X3-N to X1-N and X2-N. Align holes and hold in position. Narrow side (Direction as shown below) X2-N Wide side faces the front Direction of the slide X1-N X3-N...
- Page 34 NOTE: 3. Do not over-tighten the nuts and bolts at every step. 4. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 26 Insert the end of X4-N into X1-N and X2-N.
- Page 35 NOTE: 5. Do not over-tighten the nuts and bolts at every step. 6. Do not snap in the cover of plastic cap until you have finished the assembly of each step and went back to tighten all of the nuts and bolts. STEP 27 ...
- Page 36 WARNING: Do not let children use the playground equipment until it is properly assembled and anchored. Important Note: Please ensure that the slide is attached to the swing set as shown in the diagram. Failing to assemble in such manner will increase chances of entrapment to leg, hand and head.
- Page 37 MANUFACTURER’S LIMITED WARRANTY SPORTSPOWER LTD. Warrants its GYM products for (180) days against defects in material, workmanship and rust painted parts which compromises the structural integrity of the product when used for the purpose intended, normal conditions, and provided it receives proper care and maintenance.
Need help?
Do you have a question about the MSC-3990 and is the answer not in the manual?
Questions and answers