Advertisement
Quick Links
1.0 SAFETY INFORMATION
•
The provision of the electrical supply and the connection of the unit to the mains must be
carried out by a qualified electrician.
•
Isolate from power supply before removing any covers. During installation / maintenance ensure
all covers are fitted before switching on the mains supply.
•
All-pole disconnection from the mains as shown in the wiring diagram must be incorporated
within the fixed wiring and shall have a minimum contact separation of 3mm in accordance with
latest edition of the wiring regulations.
•
This unit must be earthed.
•
Ducting must be securely fixed with screws to the spigot to prevent access to live parts. Duct
runs terminating close to the fan must be adequately protected by suitable guards.
•
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
•
Precautions must be taken to avoid the back-flow of gases into the room from the open flue of
gas or other fuel-burning appliances.
•
This appliance should not be used by children or persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the safe use of the appliance by a person responsible for their safety.
Children shall not play with the appliance. Cleaning and user maintenance shall not be carried
out by children.
1.1 Hazard Symbols
GENERAL WARNING
Signifies a general warning regarding hazard specified by supplementary information.
ELECTRIC SHOCK
This unit must be completely electrically isolated before any panels are removed. Check
mains supply and control connections.
ROTATING PARTS
This unit contains fast moving rotational parts which may start automatically. It is the
sole responsibility of the installer to adequately guard these components.
REFER TO INSTRUCTION MANUAL
Read and understand the installation and maintenance manual before installing,
operating or maintaining this product.
Nuaire |
Western Industrial Estate
XS WA Wall Fan Kits 50 / 60Hz
Supply / Extract Units
Installation Manual
|
|
| nuaire.co.uk
Caerphilly
CF83 1NA
18. 03. 20. Document Number 671051
EMC Directive
2014/30/EU
LVD Directive
2014/35/EU
1
Advertisement
Related Manuals for NuAire XSWA Series
Summary of Contents for NuAire XSWA Series
- Page 1 REFER TO INSTRUCTION MANUAL Read and understand the installation and maintenance manual before installing, operating or maintaining this product. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate...
- Page 2 •Reusable Half Mask Respirators - when replacing filters which have been in contact with normal room or environmental air. Fan assembly Nuaire would always recommend a site specific risk assessment by a competent person to determine if any additional PPE is required. 2.0 INTRODUCTION 2.5 Dimensions (mm)
-
Page 3: Mechanical Installation
Make good around Cut the spacer to match the walls total thickness the wall sleeve. using a fine / medium cut woodsaw. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate Caerphilly CF83 1NA... - Page 4 IMPORTANT During shutter operation of XS fans there will be a short delay on start-up and shut down of approximately 40 seconds, this is normal. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate...
-
Page 5: Electrical Installation
Connect link wire between L2 & L3 for supply. Connect switched live signal to L5 for integral timer module. Refit terminal cover before replacing the electrical panel. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate... - Page 6 Up to 2 fans (size 12") can be controlled by one XS-MFC. Do not mix different fan sizes on the same controller. Plug the connector into the required sensor module. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051...
- Page 7 Push out backplate box cable entry using a screwdriver. Wall Mounting Points Push the replacement cover into the grille front. 1.5m Spot through backplate box and drill and plug the wall. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate Caerphilly...
- Page 8 Picture Frame Adaptor Connect the end of the cable into the control block. Fitting Sensor Module Fit the control into the backplate box and secure. Test the installation. Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate Caerphilly...
-
Page 9: Maintenance
The product warranty applies to the UK mainland and in accordance with Clause 14 of our Conditions of Sale. Customers purchasing from outside of the UK should contact Nuaire International Sales office for further details. Failure to maintain the unit as recommended will invalidate the warranty. - Page 10 Installation Manual XS WA NOTES Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate Caerphilly CF83 1NA...
- Page 11 Installation Manual XS WA NOTES Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate Caerphilly CF83 1NA...
- Page 12 Installation Manual XS WA NOTES Nuaire | | nuaire.co.uk 18. 03. 20. Document Number 671051 Western Industrial Estate Caerphilly CF83 1NA...
Need help?
Do you have a question about the XSWA Series and is the answer not in the manual?
Questions and answers