NetApp FAS2020 Installation And Setup

Before you begin

1
If you have not already done so, gather the required information and confirm your site
requirements, as described in the Site Requirements Guide at http://now.netapp.com/.

Install in rack

3
Four-post rack
Front rail
(2x)
Clip nut (4x)
Note: See the rail kit installation flyer included with the rail kit for the two-post procedure.

Cable the system

4
Cable controllers
RJ-45 to DB-9 adapter to console port (required)
1
0a 0b
Console cable to adapter
2
0a 0b
Network cables to e0a and e0b ports
3
0a 0b
Network cable to Remote Management port
4
6
0a 0b
Boot the system and proceed with setup
5
- Turn on the power to your system. It takes the LEDs on your system power supplies a few seconds to illuminate.
- Use the console interface and proceed through the setup questions. See the Data ONTAP Software Setup Guide at http://now.netapp.com/.
Caution: Use only the NetApp ® rail kit to install your system. Using a different rail kit can cause injury to you or damage to your system.
(2x)
(2x)
Cable disk shelves
These are a few common configurations. For additional options, see Supported Configurations for
FAS2000-series Systems at http://now.netapp.com.
Port labels
e0a e0b
Active/Active NAS or ISCSI:
1 Fibre Channel Disk Shelf Stack (Multipath)
Controller to shelf
1
8
Remote
Management
Port
Fibre
Channel
e0a e0b
8
Ethernet
Console Shelf to shelf
2
e0a e0b
8
Shelf to controller
3
e0a e0b
8
8

Unpack and verify contents

2
Your system comes with an accessory kit that includes the following components:
- This installation poster
- Software license flyer
- Grounding kit
Single Controller Dual Path
Controller to shelf
1
FAS2020
0a 0b 10101 e0a e0b
PSU PSU PSU
Controller Module B
FAS2020
0a 0b 10101 e0a e0b
0a 0b
or
DS14
DS14
OUT IN
PSU
PSU PSU
IN
IN OUT
DS14
DS14
OUT IN
PSU
PSU PSU
IN
IN
IN OUT
FAS2020
0a 0b 10101 e0a e0b
PSU PSU
Controller Module B
0a 0b 10101 e0a e0b
DS14
OUT IN
PSU PSU
IN OUT
DS14
OUT IN
PSU PSU
IN OUT
FAS2020
0a 0b 10101 e0a e0b
PSU PSU
Controller Module B
0a 0b 10101 e0a e0b
DS14
OUT IN
PSU PSU
IN OUT
DS14
OUT IN
PSU PSU
IN OUT
FAS2020 System
Installation and Setup
- Power cables
- DB-9 to RJ-45 console adapters
- Rail kit (for two-post and four-post racks)
Mounting
bracket
(2x)
Active/Active FC SAN Dual Path
Controller to switch
1
PSU
FAS2020
0a 0b 10101
10101 e0a e0b
PSU
or Controller Module B
0a 0b 10101
OUT IN
PSU DS14
OUT
OUT
PSU
IN OUT
OUT IN
DS14
PSU
OUT
OUT
PSU
IN OUT
2 Controller to shelves
FAS2020
0a 0b 10101
PSU
Controller Module B
0a 0b 10101
DS14
OUT
PSU
IN OUT
DS14
OUT
PSU
IN OUT
Copyright © 2010 NetApp, Inc. All rights reserved.
2U
3U
3U
Setting the disk shelf IDs
Shelf ID
switch
Note: The disk shelf IDs for the
disk shelves should be set in the
range 1 to 6.
Connect power
Note:
You do not need to
ground your system.
e0a e0b
PSU
e0a e0b
IN
PSU
IN
PSU
e0a e0b
PSU
e0a e0b
IN
PSU
IN
PSU
210-03961+D0