Nice NiceOne OXI Series Installation And Use Instructions And Warnings
Hide thumbs
Also See for NiceOne OXI Series:
- Installation and use instructions and warnings (145 pages)
Related Manuals for Nice NiceOne OXI Series
Summary of Contents for Nice NiceOne OXI Series
- Page 1 Installation and use instructions NiceOne and warnings Receiver OXI family OX2 family 0682 Europe: www.ApolloGateOpeners.com | (800) 878-7829 | Sales@ApolloGateOpeners.com...
- Page 2 – Models with “SM” type connection – Models with universal type connection www.ApolloGateOpeners.com | (800) 878-7829 | Sales@ApolloGateOpeners.com...
-
Page 3: Product Description And Intended Use
INTENDED USE – NiceOne receivers; – O-box programming unit; This receiver is part of the series “NiceOne” produced by Nice – Control units and gearmotors with “T4 Bus”; spa. The receivers in this series are destined for use on the –... -
Page 4: Specifications
– These models can be used exclusively with the control units fitted with an “SM” type connection (fig. 1). Note – to identify compatible control units, refer to the Nice product catalogue. • For all models – These models automatically recognise the characteristics of –... -
Page 5: Product Installation
3 – PRODUCT INSTALLATION – Jumper NOT inserted = 24 V ac/dc (voltage limits: 18 ÷ 28 V) • For models with “SM” type connection – Jumper INSERTED = 12 V ac/dc (voltage limits: 10 ÷ 18 V) These models are connected to the control unit by inserting the connector in the relative control unit connector (fig. - Page 6 ––– Electrical connections ––– Connect the 6 wires of the receiver cable to the relative termi- nals of the control unit as follows (fig. 3): • Red and Black = POWER SUPPLY (red = Positive, black = Negative. In AC this is not impor- Black tant).
- Page 7 www.ApolloGateOpeners.com | (800) 878-7829 | Sales@ApolloGateOpeners.com...
- Page 8 • For all models: PROGRAMMING THE Installation of an external aerial MAIN FUNCTIONS If the aerial supplied is in an unfavourable position and the radio signal is weak, an external aerial may be installed to improve reception (mod. ABF or ABFKIT). The new aerial must Programming warnings be positioned as high as possible and above any metal or reinforced concrete structures present in the area.
- Page 9 4 – CAUTION! – READ THIS SECTION Caution! – Before memorising a transmitter, carefully read all memorisation procedures described below to BEFORE MEMORISING THE select the one most suited to your specific application. TRANSMITTER 5 – TRANSMITTER MEMORISATION The receiver can only memorise transmitters belonging to one PROCEDURE: “Mode I”...
- Page 10 5.1 – Memorisation in “MODE I” 6 – MEMORISING A TRANSMITTER USING THE “ENABLE CODE” OF ANOTHER Warning – This procedure simultaneously memorises all keys of the transmitter or a group of the latter (on trans- TRANSMITTER [already memorised] mitters with more than one identity code). This procedure can only be used if two transmitters with 01.
- Page 11 (maximum 10-20 m from receiver). • Repeat the same procedure for each transmitter to be memorised. Standard Procedure (valid for all Nice receivers) 01. On the NEW transmitter, press and hold the key…. for at least 5 seconds (see note 1) and then release.
- Page 12 03. On the NEW transmitter, press the same key pressed in 8 – TOTAL RECEIVER MEMORY DELETION point 01 for at least 3 seconds and then release. 04. On the OLD transmitter, press the same key pressed in All transmitters memorised can be deleted from the receiver point 02 for at least 3 seconds and then release.
- Page 13 Note 1: • Led ORANGE = Both memorisation modes locked (“in If the transmitter is memorised in “Mode I” any key can be the vicinity” and with “enable code”). pressed. 04. (within 5 seconds) Press any key of a transmitter already If the transmitter is memorised in “Mode II”...
-
Page 14: Other Functions
11 – MEMORISATION OF A TRANSMITTER USING THE RECEIVER OTHER FUNCTIONS “CERTIFICATE NUMBER” [with O-Box] – This procedure can only be used if a trans- WARNING – The settings described in this chapter mitter is used with “O-Code” encoding and when in posses- require use of the O-Box or O-View programming unit. - Page 15 Initially, the procedure consists in the installer entering, with This function can be enabled (or disabled) on the receiver (fac- the aid of the programming unit “O-Box”, the required func- tory setting ON) and, when active, the receiver does not tions and the relative receiver “certificate”...
- Page 16 15 – ENABLING (or disabling) 17 – ENABLING (or disabling) THE “REPEATER” FUNCTION COMMAND DELIVERY ON THE “T4 BUS” NETWORK (Function available only on models OXIT, OXITFM, OX2T, [with O- View] – On systems in which connection is via the OX2TFM, in combination with transmitters using O-Code “T4 Bus”, if more than one receiver is installed, and there is the encoding).
-
Page 17: Disposal Of The Product
19 – PROTECTION OF PROGRAMMED DISPOSAL OF THE PRODUCT FUNCTION SETTINGS This product constitutes an integral part of the automa- tion system, therefore it must be disposed of along with it. [with O-Box / O-View] – This function enables the user to As in installation, also at the end of product lifetime, the disas- protect all programmed functions on the receiver, also dis- sembly and scrapping operations must be performed by qual-... -
Page 18: Product Technical Specifications
PRODUCT TECHNICAL SPECIFICATIONS OXIT OXIFM OXITFM • Decoding “O-Code” / “FloR” / “TTS”; or “Flo”; or “Smilo” • Maximum absorption 30 mA • Reception frequency 433.92 MHz 868.46 MHz 868.46 MHz • Transmission frequency ––– 433.92 MHz ––– • Sensitivity Above 0.5 µV Above 0.8 µV •... -
Page 19: General Notes
– All technical specifications stated in this section refer to an ambient temperature of 20°C (± 5°C). – Nice reserves the right to apply modifications to the product at any time when deemed necessary, while maintaining the same functionalities and intended use. - Page 20 Table A been re-synchronised 4 5 = Output in “Mode II” not managed on control unit 5 5 = During deletion procedure, indicates that the code SIGNALS EMITTED BY THE has been deleted RECEIVER LED 5 5 = “Certificate” with higher priority that the admissible value ––...
-
Page 21: Ec Declaration Of Conformity
A copy of the original declaration for each product can be requested from Nice S.p.a. (TV) I. The undersigned, Lauro Buoro, in the role of Managing Director, declares under his sole responsibility, that the product: Manufacturer’s name : Nice S.p.a. - Page 22 A copy of the original declaration for each product can be requested from Nice S.p.a. (TV) I. The undersigned, Lauro Buoro, in the role of Managing Director, declares under his sole responsibility, that the product: Manufacturer’s name : Nice S.p.a.
Need help?
Do you have a question about the NiceOne OXI Series and is the answer not in the manual?
Questions and answers