INTRODUCTION ® Thank You for Purchasing a PowerSmart Product. This manual provides information regarding the safe operation and maintenance of this product. Every effort has been made to ensure the accuracy of the ® information in this manual. PowerSmart reserves the right to change this product and specifications at any time without prior notice.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your high pressure washer works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.
Page 6
USE ONLY THREE-WIRE EXTENSION CORDS that have 3-pronged plugs and outlets that accept the tool's plug as shown in Fig. A. Repair or replace a damaged or worn cord immediately. CAUTION: In all cases, make certain the outlet in question is properly grounded. If you are not sure if it is, have a licensed electrician check the outlet.
PERSONAL SAFETY The high pressure washer may not be directed at persons, animals, live electrical equipment or at the appliance itself. Keep bystanders away . All visitors and pets should be kept a safe distance away from the work area. ...
Vehicle tyres or tyre valves are susceptible to damage from the high pressure washer and may burst. The first indication of this is a discoloration of the tyre. Damaged vehicle tyres/tyre valves are highly dangerous. Ensure that a distance of at least 30 cm is observed when cleaning with the washer. Risk of explosion.
KNOWING YOUR HIGH PRESSURE WASHER Water supply connector High pressure hose Water outlet Water inlet ON/OFF switch Transport handle Detergent tank Power cord Wheels Trigger gun Spray lance Safety lock Hose lock Trigger handle holder Fig.1 Trigger handle locker Unpacking Retractable rod Detergent suction pipe Unpack the power tool and all its parts, and compare...
ASSEMBLY INSTRUCTION WARNING: Do not use this product if any parts on the packing list are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.
OPERATING INSTRUCTION WARNING: Prior to cleaning, make sure that the high pressure washer is placed safely on level ground. Wear protective goggles and protective clothing during the cleaning process. Notes: Release the lever of the trigger gun, the device will switch off again. High pressure washer remains in the system.
Page 12
Turn the water supply tap on completely. Make sure the safety lock is down and in its original position (Fig.9) , then press the trigger for a few seconds until water flow is steady. This will allow air to escape and discharge any residual pressure in the hose.
Page 13
To disconnect a nozzle from the spray wand Turn off the pressure washer and shut off the water supply. Pull the trigger to release water pressure. Engage the safety lock on the trigger handle . Remove the nozzle by placing your hand over the nozzle while pulling back on the Quick-Connect ...
MAINTENANCE WARNING: In order to avoid personal injury and the risk of fire and electric shock, turn off the appliance and remove the mains plug prior to any care and maintenance work. WARNING: When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage.
SCHEMATIC DRAWING Fig.16 TROUBLE SHOOTING WARNING: Read instruction manual first! Remove plug from power source before making adjustments or assembling accessories. Problem Possible Cause Possible Solution 1.Machine not plugged in 1.Plug in machine 2.Defective socket 2.Try another socket 3.Defective extension cable 3.Try another extension cable Appliance is not running 4.Incorrect mains voltage...
PARTS LIST Item Stock# Description Qty. Item Stock# Description Qty. ST4X16 SELF CHECK VALVE PS2020-001 PS2020-032 TAPPING SCREW SPRING MOTOR COVER PS2020-002 PS2020-033 CHECH VALVE BASE PS2020-003 MOTOR COVER PS2020-034 Φ11.5XΦ1.8 O RING PS2020-004 MOTOR HC8849JM PS2020-035 CHECK VALVE PLUG...
Page 18
LIQUID-ABSORBENT PS2020-063 PS2020-094 WHEEL CAP JOINT PS2020-064 Φ6XΦ2 O RING PS2020-095 M5X12 HEX BOLT LIQUID-ABSORBENT BT5X16 SELF-TAPPING PS2020-065 PS2020-096 CORE TUBE SCREW PS2020-066 Φ2.5XΦ1 O RING PS2020-097 BOTTLE BACKFLOW HOLE PS2020-067 PS2020-098 BOTTLE LID PLUG PS2020-068 SWITCH WIRE PS2020-099 PVC SOFT TUBE...
Limited Warranty, you must return the entire power tool product; transportation prepaid, to PowerSmart Include a legible copy of the original receipt, which lists the date of purchase (month and year) and the name of the company purchased from.
Need help?
Do you have a question about the PS2020 and is the answer not in the manual?
Questions and answers
where can I purchase a replacement wand [ trigger gun]for this model ps2020