Advertisement
Quick Links
ARDWICK Ottoman TV Bed
Important before assembly:
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid
scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep these instructions for future reference.
Assembly Instructions
Title of Product
.
.
www.happybeds.co.uk
Advertisement
Related Manuals for Happybeds ARDWICK Ottoman TV Bed
Summary of Contents for Happybeds ARDWICK Ottoman TV Bed
- Page 1 Assembly Instructions Title of Product ARDWICK Ottoman TV Bed Important before assembly: Read these instructions carefully before assembling or using the product. Please check the contents of the boxes before attempting to assemble this product. The instructions will have a checklist of parts and fittings.
- Page 2 Never drag or push the pieces across a hard or stone floor as this will cause damage to the joints. Use a carpet or a rug for extra care. If you have problems assembling or have damaged or missing pieces, please contact us by visiting: https://www.happybeds.co.uk/customer-service...
- Page 3 ARDWICK OTTOMAN TV BED ASSEMBLY INSTRUCTIONS 2 Hrs If Media Tray is wanted If Media Tray is wanted on on left side, fit side rail (3) right side, fit side rail (3) to to left and (4) to right. right and (4) to left.
- Page 4 CARTON 1 - HEADBOARD CARTON 2 - FOOTBOARD HEADEND CONNECTION FOOTEND CONNECTION FOR USB - CABLE (P) FOR USB - CABLE (P) The following items are in an accessory box, inside the TV Compartment within the Footboard Hardware Pack for Bed Assembly Hardware Pack for Media Tray Assembly A x16 B x16...
- Page 5 HARDWARE PACK FOR ASSEMBLY OF OTTOMAN SLAT FRAME - INSIDE PACK 4 A x8 B x22 Q x6 DOUBLE & KING x32 SUPER KING Fitting gas-lift mechanisms U(a) & U(b) to Headboard & Spring Washers (for M8 bolts) Footboard (1&2) Flat Washers (for M8 bolts) Nuts (for M8 slat frame bolts) S x2...
- Page 6 CHOOSE WHICH SIDE YOU WANT TO LIFT UP OPEN FROM LEFT U(a) U(b) CHECK THIS DIAGRAM AND IF ACCESS IS NEEDED FROM LEFT SIDE OF BED, FIT BOTH LIFT MECHANISMS TO RIGHT SIDE OF THE BED. BOLT INTO THE HOLES MARKED (R) WITH BLUE LABELS. THE MECHANISMS ARE LABELED U(a) &...
- Page 7 OPEN FROM RIGHT U (a) U (b) CHECK THIS DIAGRAM AND IF ACCESS IS NEEDED FROM RIGHT SIDE OF BED, FIT BOTH LIFT MECHANISMS TO LEFT SIDE OF THE BED. BOLT INTO THE HOLES MARKED (L) WITH RED LABELS. THE MECHANISMS ARE LABELED U(a) &...
- Page 8 1&2 3&4 DO NOT TIGHTEN BOLTS FULLY Page 6 of 21...
- Page 9 Fit the base board support rails (12) to both side rails. IMPORTANT: Be careful not to scratch the PU or fabric when slotting the wooden supports into the side rail brackets. 3&4 LEFT 100% N.B. SQUARE UP BED AND THEN TIGHTEN ALL BOLTS 100% Always to LEFT side rail 3 or 4, irrespective of which side is chosen to be plain or with media tray, fit USB/Headphone...
- Page 10 Connect SOCKET in Footend to Connect PLUG in Headend to on connection cable SOCKET on connection cable PLUG FOOTEND HEADEND Connect Main Power Lead (G) to your wall socket - for safety, this must be an earthed supply. Page 8 of 21...
- Page 11 Press the “UP” button to raise the TV lift. Note: For illustration purposes only, TV connections may vary. TIP: BEFORE FITTING THE TV, PUSH CABLES THROUGH EACH DUCT FROM THE TOP. CHOOSE THE BEST SIDE TO HDMI USE DEPENDING ON WHERE THE CONNECTION PORTS ARE, ON BACK OF YOUR TV.
- Page 12 TV Installati o n - Normal Vesa Fixing IF SCREWS ARE SUPPLIED WITH TV, PLEASE USE THOSE IN PREFERENCE Counter-Sunk Counter-Sunk Screws Screw-Washer a x2 sets (M8x25mm) - (M6x12mm) Screws (M4x12mm) Use 5mm Allen Key (D) b x2 Allen Key (4mm) Allen Key (2.5mm) Loosen Tighten...
- Page 13 TV Installation - 100x100 Vesa Fixing REMOVE CROSS-BRACKET AND FIX IT DIRECTLY TO BACK OF TV 100mm IF SCREWS ARE SUPPLIED WITH TV, PLEASE USE THOSE IN PREFERENCE Screw-Washer sets a x2 Counter-Sunk Counter-Sunk Screws (M8x25mm). (M6x12mm) Screws (M4x12mm) Use 5mm Allen Key (D) b x2 Allen Key (4mm) Allen Key (2.5mm)
- Page 14 TV Installation - 100x100 Vesa Fixing Loosen Tighten Page 12 of 21...
- Page 15 Note: For illustration purposes only, TV connections may vary. TV Power Lead supplied with your own TV 90º ADAPTOR REMOVE DUST-CAP OPTICAL PLUG IN - KEEP ALL CABLES TIGHT - USE CLIPS & TIES PROVIDED. Keep wires tight - peel off cover from cable clips &...
- Page 16 TV Power Lead supplied with your TV Press the “DOWN” button to lower the TV lift. Page 14 of 20...
- Page 17 Page 15 of 21...
- Page 18 DOUBLE & KING x4 SUPER KING x6 & DOUBLE or KING SUPER KING CAREFULLY FIT CROSS BAR (14) FOR ADDITIONAL STRENGTH Page 16 of 21...
- Page 19 Slat Frame Support Bar 1&2 IMPORTANT: Be careful to keep the two HDMI Leads (H) on top of the Base Boards - Main power lead (G) and Aerial lead (J) should be kept under the base boards & fed out under the Headboard so you can connect to your wall sockets.
- Page 20 Carefully lay frame down. Make sure there is an even gap each side of about 8 mm, as in the sketch. Hold frame securely then tighten all six bolt sets 100% using spanner (T) & Allen key (D). Note: Be very careful what you store under the bed - the top of an item, like a suitcase or a box must not...
- Page 21 FIT THE REMOTE CONTROL HOLSTER FIT THE MATTRESS STOPPERS LEFT OR RIGHT TV BED SAFETY INFORMATION GENERAL INFORMATION It is very important not to place any vessel containing liquids, e.g. drinks or vase of flowers, on top of the TV footboard which may accidentally spill and enter the TV compartment as this could cause damage to the TV and/or the TV lifting equipment.
-
Page 22: Television Installation
TV BED SAFETY INFORMATION TELEVISION INSTALLATION Before fixing the slats frame to the bed, please follow the television installation instructions below Raise the TV Lift by pressing the TOP button of the remote control. Connect the TV using the TV Installation hardware packed in the accessory box in Carton 2. Connect the TV to the mounting bracket plate as in Step 10 or 11. - Page 23 conforms of 14 Kg ". : W97 x H55 x D8 cm Periodically remove dust by using a light vacuum cleaner or if your bed is PU, use a soft damp cloth. We cannot be held responsible for any damage caused to the TV, TV cabling or the TV Bed itself due to incompatibility of any additional equipment installed by the end-user or due to loose and poorly installed cables (see Step 9 ).
- Page 24 floor as this will cause damage to the joints and could result in failure to the product that will invalidate the warranty. For more information on cleaning and product care visit: https://www.happybeds.co.uk/help-and-advice Notes We’ve tried to make this product as easy to assemble as possible. In the unlikely event that...
Need help?
Do you have a question about the ARDWICK Ottoman TV Bed and is the answer not in the manual?
Questions and answers