Advertisement
Quick Links
2GIG-PAD1-345
WIRELESS KEYPAD
INSTALLATION INSTRUCTIONS
The 2GIG Wireless Keypad (2GIG‐PAD1‐345) is a wall‐mounted unit
designed for use as a secondary keypad for the 2GIG security system.
It communicates with the Control Panel using the 345 MHz frequency
and provides users with the following features:
• Arm the system in Stay or Away mode
• Disarm the system
• Activate Fire and Panic emergency functions
Figure 1 Wireless Keypad
Contents
Verify that the package includes the following:
• 1—Wireless Keypad
• 4—Plastic Wall Anchors and Phillips Head Screws
• 2—Lithium Coin Batteries (installed)
Programming
Use the Control Panel to configure the Wireless Keypad to work with
the security system. For details, see "Wireless (RF) Keypad
Programming" in the Control Panel's Installation & Programming
Guide.
Testing
Before mounting the Wireless Keypad in the desired location, verify
that the location provides for good radio frequency (RF)
communication to the Control Panel.
To test the Wireless Keypad:
1
Place the Control Panel into sensor test mode. For instructions,
see the Control Panel's Installation & Programming Guide.
Press and hold any numeric key on the Wireless Keypad for at least
2
two (2) seconds.
Listen for a siren or keypad beeps to determine the appropriate
3
response. For information, see the Control Panel's Installation &
Programming Guide
Exit sensor test mode.
4
NOTE:
It is strongly recommended that you perform a system test
using the instructions in the Control Panel's Installation &
Programming Guide.
Mounting the Wireless Keypad
To mount the Wireless Keypad:
1
Simultaneously press the hinged tabs on top of the Wireless
Keypad to separate the mounting plate from the keypad. See in
Figure 2 below.
—
Figure 2 Wireless Keypad
Hinged Tabs
Place the mounting plate in the desired location on the wall. Then
2
ensure the mounting plate is level.
Secure the mounting plate to the wall using the four (4) Plastic
3
Wall Anchors and Phillips Head Screws (provided). See Figure
2 below.
—
Figure 3 Wireless Keypad
Mounting Plate
Copyright © 2015 Nortek Security & Control LLC
1
Advertisement
Related Manuals for Nortek Security & Control 2GIG 2GIG-PAD1-345
Summary of Contents for Nortek Security & Control 2GIG 2GIG-PAD1-345
- Page 1 2GIG-PAD1-345 WIRELESS KEYPAD INSTALLATION INSTRUCTIONS Mounting the Wireless Keypad To mount the Wireless Keypad: The 2GIG Wireless Keypad (2GIG‐PAD1‐345) is a wall‐mounted unit designed for use as a secondary keypad for the 2GIG security system. Simultaneously press the hinged tabs on top of the Wireless It communicates with the Control Panel using the 345 MHz frequency Keypad to separate the mounting plate from the keypad. See in and provides users with the following features: Figure 2 below. • Arm the system in Stay or Away mode — Figure 2 Wireless Keypad Hinged Tabs • Disarm the system • Activate Fire and Panic emergency functions Figure 1 Wireless Keypad Contents Place the mounting plate in the desired location on the wall. Then Verify that the package includes the following: ensure the mounting plate is level. • 1—Wireless Keypad Secure the mounting plate to the wall using the four (4) Plastic ...
- Page 2 SPECIFICATIONS Connect the batteries by removing the two battery pull tabs. The pull tabs are located near the metal clips on each battery. See Wireless Signal Range 350 ft (106.7 m), open air, with Wireless Figure 4 below. Control Panel Figure 4 Wireless Keypad—Battery Compartment Code Outputs Key Press 0‐9; *; #; Stay; Away; Fire; Police; Supervisory; Low Battery Transmitter Frequency 345.00 MHz (crystal controlled) Unique ID Codes Over one (1) million different code combinations Supervisory Interval 70 minutes 5.73 x 4.25 x 1.00 in (14.6 x 0.8 x 2.5 cm) Dimensions (L x W x H) Weight (including battery) 7.75 oz (219.7 g) Housing Material ABS Plastic Color White with Silver Trim Operating Temperature 32° to 120° F (0° to 49° C) Relative Humidity 5‐90% Non‐Condensing Battery (installed) Two (2) CR 2032 3V or equivalent Lithium coin batteries Certification Anatel, ETL, FCC, IC, IFETEL, and NOM REGULATORY INFORMATION Metal Clips Hinged Tabs Reattach the mounting plate to the unit by aligning the bottom of ...
- Page 3 LIMITED WARRANTY Industry Canada (IC) Compliance This device complies with Industry Canada license‐exempt RSS This Nortek Security & Control LLC product is warranted against standard(s). Operation is subject to the following two conditions: (1) defects in material and workmanship for two (2) years. This warranty this device may not cause interference, and (2) this device must accept extends only to wholesale customers who buy direct from Nortek any interference, including interference that may cause undesired Security & Control LLC or through Nortek Security & Control LLC’s operation of the device. normal distribution channels. Nortek Security & Control LLC does not Repairs to certified equipment should be made by an authorized warrant this product to consumers. Consumers should inquire from Canadian maintenance facility designated by the supplier. Any repairs their selling dealer as to the nature of the dealer’s warranty, if any. or alterations made by the user to this equipment, or equipment There are no obligations or liabilities on the part of Nortek Security & malfunctions, may give the telecommunications company cause to Control LLC for consequential damages arising out of or in connection request the user to disconnect the equipment. with use or performance of this product or other indirect damages Users should ensure for their own protection that the electrical with respect to loss of property, revenue, or profit, or cost of removal, ground connections of the power utility, telephone lines and internal installation, or reinstallation. All implied warranties for functionality, metallic water pipe system, if present, are connected together. This are valid only until the warranty expires. This Nortek Security & precaution may be particularly important in rural areas. Control LLC Warranty is in lieu of all other warranties expressed or implied. Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. 2GIG 1950 Camino Vida Roble, Suite 150 Carlsbad, CA 92008 USA For technical support in the USA and Canada: Dial: 855‐2GIG‐TECH (855‐244‐4832)
Need help?
Do you have a question about the 2GIG 2GIG-PAD1-345 and is the answer not in the manual?
Questions and answers