Sundown Audio SALT-4 Owner's Manual

High performance car amplifier, monoblock, multi-channels

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

OWNER'S MANUAL

HIGH PERFORMANCE CAR AMPLIFIER

Mono Blocks:

SALT - 4

SALT - 6

SALT - 8

SALT - 12

Multi - Channels:

SALT - 200.2

SALT - 400.2

SALT - 200.4

SALT - 300.4

SALT - 500.4

Table of Contents

Need help?

Do you have a question about the SALT-4 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sundown Audio SALT-4

Page 1 OWNER’S MANUAL Mono Blocks: SALT - 4 SALT - 6 SALT - 8 SALT - 12 Multi - Channels: SALT - 200.2 SALT - 400.2 SALT - 200.4 SALT - 300.4 SALT - 500.4 HIGH PERFORMANCE CAR AMPLIFIER...
Page 2 24 dB/Octave - Variable Subsonic Filter Wired Remote Control with Voltage & Temperature display and Clipping Indicator. DIGITAL MONOBLOCK SPECIFICATIONS Rated Power Output ( Tested Voltage 14.4Volts ) SALT-4 SALT-6 SALT-8 SALT-12 - RMS Power - 2ohms Linked : 8000w...
Page 3 FULL RANGE DIGITAL FEATURES Full Range Digital Amplifiers Crossover Multipliers - X1 / X10 High Efficiency Digital Multi-Channel Design Clipping Indicator Stable - 2ohm Stereo / 4ohm Bridged 4 Way Protection Circuit ( Thermal, Voltage 12 dB/Octave - Variable Subsonic Filter Speaker short and DC Offset ) 12 dB/Octave - Variable High Pass Filter Optional Wired Remote Control with Voltage &...
Page 4 : 9V-15.5Volts BATTERY GROUND SALT-500.4 : 9V-15.5Volts SALT-4, SALT-6, SALT-8, SALT-12, SALT-200.2, SALT-400.2, SALT-200.4, SALT-300.4 & SALT-500.4 are not supplied with internal fuse in themselves. Make sure you install in-line fuse holder from Positive terminal of Battery +12V Battery You need to connect a power wire to the vehicle’s positive battery terminal. This connection must be tight and secure to ensure proper connectivity.
Page 5 DIGITAL MONOBLOCK INPUT CONNECTION HEADUNIT Wired Remote Control DIGITAL MONOBLOCK SPEAKER CONNECTIONS 8~1ohms 8~2ohms 8~2ohms...
Page 6 DUAL AMP INPUT CONNECTION ( MASTER & SLAVE ) MASTER amp HEADUNIT Wired Remote Control SLAVE amp...
Page 7 DUAL AMP CONNECTION ( MASTER & SLAVE ) MASTER amp HEADUNIT 8~2ohms Wired Remote Control SLAVE amp Using a dual amplifier configuration, the MASTER amplifier has total control over the SLAVE amplifier. When using dual amplifier to operate subwoofer, the positive terminal of the subwoofer's voice coil must be connected to the positive terminal of the MASTER amplifier and the negative terminal of the subwoofer's voice coil must be connected to positive terminal of the SLAVE amplifier.
Page 8 FULL RANGE DIGITAL 2CH INPUT CONNECTION HEADUNIT Wired Remote Control ( Optional ) FULL RANGE DIGITAL 2CH SPEAKER CONNECTION SALT-200.2 & SALT-400.2 - 2 Channel Speaker Connection Mode. Tweeter Passive MidRange /Bass SALT-200.2 & SALT-400.2 - 3 Channel Speaker Connection Mode. Tweeter Passive MidRange...
Page 9 FULL RANGE DIGITAL 4CH INPUT CONNECTION HEADUNIT Wired Remote Control ( Optional ) FULL RANGE DIGITAL 4CH SPEAKER CONNECTION SALT-200.4, SALT-300.4 & SALT-500.4 - 3 Channel Speaker Connection Mode. Tweeter Passive MidRange /Bass 8~4ohms...
Page 10 SALT-200.4, SALT-300.4 & SALT-500.4 - 4 Channel Speaker Connection Mode. Tweeter Passive MidRange /Bass SALT-200.4, SALT-300.4 & SALT-500.4 - 5 Channel Speaker Connection Mode. Tweeter Passive MidRange /Bass 8~4ohms...
Page 11 Check the nominal load impedance to verify that the amplifier is driving a load equal to or greater than 1 ohm for SALT-4, SALT-6, SALT-8 and SALT-12 or 2ohm stereo or 4ohm bridged for SALT-200.2, SALT-400.2, SALT-200.4, SALT-300.4 and SALT-500.4.
Page 12 514 W 21st Street, Newton, NC 28658 Find us on : www.sundownaudio.com...

This manual is also suitable for:

Salt-6 Salt-8 Salt-12 Salt-200.2 Salt-400.2 Salt-200.4 ... Show all